AZ Floor Covering Contractors License
(Classification: CR-8) Questions And
Answers With Correct Update
Not enough thinset - Answer - What would happen if you applied thinset with a small notched trowel on
large tile?
Flooring that has surfaces with no give - Answer - What is "non-resilient" flooring?
4 groups - Answer - The marble institute of America has classified marble and stone into how many
groups?
10 - Answer - When blind nailing 6ft plank flooring, how many nails are used per plank?
6 inches - Answer - The maximum allowable spacing when using 8d nails to fasten the edges of 5/8 inch
thick plywood to floor joists is how many inches on the center?
1/8 inch on ends and edges - Answer - When applying plywood sub-flooring the minimum spacing
between adjacent panels at the edge is?
15lb felt paper - Answer - Before nailing wood flooring down on plywood sub-floor, what do you put
down?
16d - Answer - What nails do you use to fasten a loose subfloor with 1&1/4 inch thickness?
Coped - Answer - A carpenter is installing a decorative baseboard trim that will be stained. According to
carpentry and building construction, what type of joint should be used for a 90° inside corner when the
installer is using the best method for quality construction?
, Misted - Answer - Semi-vitreous tile that is to be grouted with portland cement grout should first be:
15 pound roofing felt or 4 mil polyethylene - Answer - Ceramic tile is to be installed using the "one coat"
method over gypsum board on wood studs; the "Tile Council of America" recommends that the
membrane be:
Performance of a layout - Answer - What is the most important consideration in the production of a
professional looking tile job?
Band saw - Answer - The ideal tool for cutting parquet is?
4% - Answer - Before gluing flooring to a sub-floor the difference in moisture content between the
flooring and the sub-floor should not be more than:
Second grade - Answer - What grade of maple (marble?) has a mixture of colors and some defects?
Grout - Answer - If not sealed properly, quarry tile can be permanently damaged by:
Comb in one direction only - Answer - What should you do to increase adhesion on large tiles?
Counter tops - Answer - What is Saltillo tile not good for?
7-9 - Answer - What is the perfect PH level for concrete when gluing down carpet?
Tile set with water base thin-set - Answer - What could cause stone tile to wear?
Round shaping stone - Answer - What tool is used to shape or alter the edges of a stone tile?
85° Fahrenheit - Answer - What is the maximum temperature for radiant heated floors before installing
carpet?
(Classification: CR-8) Questions And
Answers With Correct Update
Not enough thinset - Answer - What would happen if you applied thinset with a small notched trowel on
large tile?
Flooring that has surfaces with no give - Answer - What is "non-resilient" flooring?
4 groups - Answer - The marble institute of America has classified marble and stone into how many
groups?
10 - Answer - When blind nailing 6ft plank flooring, how many nails are used per plank?
6 inches - Answer - The maximum allowable spacing when using 8d nails to fasten the edges of 5/8 inch
thick plywood to floor joists is how many inches on the center?
1/8 inch on ends and edges - Answer - When applying plywood sub-flooring the minimum spacing
between adjacent panels at the edge is?
15lb felt paper - Answer - Before nailing wood flooring down on plywood sub-floor, what do you put
down?
16d - Answer - What nails do you use to fasten a loose subfloor with 1&1/4 inch thickness?
Coped - Answer - A carpenter is installing a decorative baseboard trim that will be stained. According to
carpentry and building construction, what type of joint should be used for a 90° inside corner when the
installer is using the best method for quality construction?
, Misted - Answer - Semi-vitreous tile that is to be grouted with portland cement grout should first be:
15 pound roofing felt or 4 mil polyethylene - Answer - Ceramic tile is to be installed using the "one coat"
method over gypsum board on wood studs; the "Tile Council of America" recommends that the
membrane be:
Performance of a layout - Answer - What is the most important consideration in the production of a
professional looking tile job?
Band saw - Answer - The ideal tool for cutting parquet is?
4% - Answer - Before gluing flooring to a sub-floor the difference in moisture content between the
flooring and the sub-floor should not be more than:
Second grade - Answer - What grade of maple (marble?) has a mixture of colors and some defects?
Grout - Answer - If not sealed properly, quarry tile can be permanently damaged by:
Comb in one direction only - Answer - What should you do to increase adhesion on large tiles?
Counter tops - Answer - What is Saltillo tile not good for?
7-9 - Answer - What is the perfect PH level for concrete when gluing down carpet?
Tile set with water base thin-set - Answer - What could cause stone tile to wear?
Round shaping stone - Answer - What tool is used to shape or alter the edges of a stone tile?
85° Fahrenheit - Answer - What is the maximum temperature for radiant heated floors before installing
carpet?
