HEAVY TRUCK STEERING AND SUSPENSION MICHIGAN MECHANIC STUDY GUIDE 2025/2026 EXAM QUESTIONS AND ANSWERS | 100% PASS

HEAVY TRUCK STEERING AND
SUSPENSION MICHIGAN MECHANIC
STUDY GUIDE 2025/2026 EXAM
QUESTIONS AND ANSWERS | 100%
PASS



YOU HAVE REPLACED A POWER STEERING PUMP WHICH FAILED.

WHAT SHOULD YOU DO BEFORE PUTTING THE TRUCK BACK INTO

SERVICE? - 🧠 ANSWER ✔✔A. REPLACE THE HYDRAULIC LINES.


B. REMOVE AIR WITH A PRESSURE BLEEDER. (NOT CORRECT

AWNSER)

C. FLUSH THE SYSTEM WITH CLEAN POWER STEERING FLUID.

(POSSIBLE CORRECT AWNSER)

D. ALL OF THE ABOVE. (NOT CORRECT AWNSER)

IN THE TANDEM SETUP SHOWN BELOW, RUBBER BUSHINGS

WOULD BE FOUND AT: - 🧠 ANSWER ✔✔A. POINT B.


B. POINT C.


1
COPYRIGHT©PROFFKERRYMARTIN 2025/2026. YEAR PUBLISHED 2025. COMPANY REGISTRATION NUMBER: 619652435. TERMS OF USE.
PRIVACY STATEMENT. ALL RIGHTS RESERVED

,C. POINT A. (CORRECT AWNSER)

D. ALL OF THE ABOVE. (NOT CORRECT AWNSER)

AFTER YOU HAVE PUT ON A NEW TIE ROD END, WHAT SHOULD

YOU CHECK AND CORRECT IF NECCESSARY? - 🧠 ANSWER ✔✔A.

CAMBER. (NOT CORRECT AWNSER)

B. WHEEL TURN ANGLE.

C. TOE SETTING. (CORRECT AWNSER)

D. CASTER.

TO REMOVE KING PIN DRAW KEYS FROM THE AXLE BEAMS, YOU

SHOULD: - 🧠 ANSWER ✔✔A. DRIVE THEM OUT FROM THE SMALL

END WITH A SOFT DRIFT. (POSSIBLE CORRECT AWNSER)

B. HEAT THE BEAM AND TAP THEM OUT. (NOT CORRECT AWNSER)

C. USE A SHOCK PULLER THREADED INTO THE LARGE END OF THE

KEYS.

D. FIRST DRILL OUT THE MIDDLE OF THE KEYS TO WEAKEN THEM,

THEN DRIFT THEM OUT. (NOT CORRECT AWNSER)




2
COPYRIGHT©PROFFKERRYMARTIN 2025/2026. YEAR PUBLISHED 2025. COMPANY REGISTRATION NUMBER: 619652435. TERMS OF USE.
PRIVACY STATEMENT. ALL RIGHTS RESERVED

, WHICH OF THESE WILL CAUSE RAPID OR UNEVEN TIRE WEAR IF

SET INCORRECTLY? - 🧠 ANSWER ✔✔A. STEARING GEAR PRELOAD.


B. CASTER.

C. CAMBER. (CORRECT AWNSER)

D. ALL OF THE ABOVE. (NOT CORRECT AWNSER)

THE POSITION OF THE FRONT TIRES IN THE DRAWING BELOW

INDICATES TOO MUCH: - 🧠 ANSWER ✔✔A. TOE IN. (NOT CORRECT

AWNSER)

B. POSITIVE CASTER. (NOT CORRECT AWNSER)

C. NEGATIVE CAMBER.

D. POSITIVE CAMBER. (CORRECT AWNSER)

IN REFERENCE TO THE BELOW ILLUSTRATION, WHICH STATEMENT

IS CORRECT? - 🧠 ANSWER ✔✔A. THE STEERING ARM IS LOCATED

AT POINT Z.

B. THE PITMAN ARM IS LOCATED AT POINT X. (NOT CORRECT

AWNSER)

C. THE DRAG LINK IS LOCATED AT POINT Y. (CORRECT AWNSER)


3
COPYRIGHT©PROFFKERRYMARTIN 2025/2026. YEAR PUBLISHED 2025. COMPANY REGISTRATION NUMBER: 619652435. TERMS OF USE.
PRIVACY STATEMENT. ALL RIGHTS RESERVED