Terms in this set (111)
Quiz____?
When using a crane to lift a 12,000-gallon tank out of the excavation, what is the
preferable position of the rigging lines attached to the tank's lifting eyes?
A. One lifting line should be horizontal
B. The lifting lines should be as far apart as possibles
C. The lifting lines should be as horizontal as possible
D. The lifting lines should be as vertical as possible -
Answer✓✓
The lifting lines should be as vertical as possible
Quiz____?
Which of the following describes surfacing ACM?
A. Material that contains more than 1% asbestos
Page 1 of 57
,B. Material that contains more than 0.1% asbestos
C. Material that contains more than 0.01% asbestos
D. Material that contains more than 0.001% asbestos -
Answer✓✓
Material that contains more than 1% asbestos
Quiz____?
When removing asbestos as a multi-employer work site, the asbestos abatement
contractor must do which of the following?
A. Ensure that all other employers leave the site
B. Inform the local Cal/OSHA office within 48 hours
C. Ensure that all asbestos is removed
D. Inform each of the employers about the asbestos work being performed. -
Answer✓✓
Inform each of the employers about the asbestos work being performed
Quiz____?
When must a contractor provide and require the use of protective clothing?
A. When Class II work requires removal of ACM exceeding 10 square feet
Page 2 of 57
,B. When airborne exposure exceeds the TWA and excursion limits
C. When Class II work requires removal of TSI exceeding 25 linear feet
D. When a negative exposure assessment is produced -
Answer✓✓
When airborne exposure exceeds the TWA and excursion limits
Quiz____?
Alternating current would most likely be used in GTAW to weld which of the following
metals?
A. Low carbon steel
B. Deoxidized copper
C. Aluminum
D. Stainless steel -
Answer✓✓
Aluminum
Quiz____?
WHat is the minimum thickness of steel that is covered by the AWS D1.1 Structural
Steel welding code?
Page 3 of 57
, A. 1/8"
B. 1/4"
C. 5/16"
D. 3/8" -
Answer✓✓
1/8"
Quiz____?
When welding with FCAW, how can the operator control excess spatter?
A. Change the drag angle
B. Run stringer beads.
C. Shorten the stickout
D. Lengthen the stickout -
Answer✓✓
Shorten the stickout
Quiz____?
To read and properly interpret laboratory analysis reports as they apply to hazardous
sites, a contractor should have which of the following?
Page 4 of 57
Quiz____?
When using a crane to lift a 12,000-gallon tank out of the excavation, what is the
preferable position of the rigging lines attached to the tank's lifting eyes?
A. One lifting line should be horizontal
B. The lifting lines should be as far apart as possibles
C. The lifting lines should be as horizontal as possible
D. The lifting lines should be as vertical as possible -
Answer✓✓
The lifting lines should be as vertical as possible
Quiz____?
Which of the following describes surfacing ACM?
A. Material that contains more than 1% asbestos
Page 1 of 57
,B. Material that contains more than 0.1% asbestos
C. Material that contains more than 0.01% asbestos
D. Material that contains more than 0.001% asbestos -
Answer✓✓
Material that contains more than 1% asbestos
Quiz____?
When removing asbestos as a multi-employer work site, the asbestos abatement
contractor must do which of the following?
A. Ensure that all other employers leave the site
B. Inform the local Cal/OSHA office within 48 hours
C. Ensure that all asbestos is removed
D. Inform each of the employers about the asbestos work being performed. -
Answer✓✓
Inform each of the employers about the asbestos work being performed
Quiz____?
When must a contractor provide and require the use of protective clothing?
A. When Class II work requires removal of ACM exceeding 10 square feet
Page 2 of 57
,B. When airborne exposure exceeds the TWA and excursion limits
C. When Class II work requires removal of TSI exceeding 25 linear feet
D. When a negative exposure assessment is produced -
Answer✓✓
When airborne exposure exceeds the TWA and excursion limits
Quiz____?
Alternating current would most likely be used in GTAW to weld which of the following
metals?
A. Low carbon steel
B. Deoxidized copper
C. Aluminum
D. Stainless steel -
Answer✓✓
Aluminum
Quiz____?
WHat is the minimum thickness of steel that is covered by the AWS D1.1 Structural
Steel welding code?
Page 3 of 57
, A. 1/8"
B. 1/4"
C. 5/16"
D. 3/8" -
Answer✓✓
1/8"
Quiz____?
When welding with FCAW, how can the operator control excess spatter?
A. Change the drag angle
B. Run stringer beads.
C. Shorten the stickout
D. Lengthen the stickout -
Answer✓✓
Shorten the stickout
Quiz____?
To read and properly interpret laboratory analysis reports as they apply to hazardous
sites, a contractor should have which of the following?
Page 4 of 57
