ROOFING PRACTICE EXAMNEWEST ACTUAL 2025/2026 TEST 1
WITH QUESTIONS AND ACCURATE ANSWERS GRADED A+
A(n) ______ is a material that is sometimes used in the process
of seaming single-ply membranes to prepare the surfaces and
increase the shear strength of the field splice. - ---Answers--
-primer
What is the minimum thickness for an aluminum standing
seam roof with a 22-3/4" pan width? - ---Answers---.040"
What is the temperature range for Type III asphalt applied with
a mop application? - ---Answers---430 degrees F +/- 25
degrees F
When installing the base sheet of a built-up roof system over
plywood decking, nail all laps at________ centers. - ---
Answers---9"
When installing wood shakes or wood shingles, the units in the
starter course should be laid so that the butt ends extend
about ______ beyond the finish fascia board. - ---Answers---1-
1/2"
, According to the Florida Building Code, underlayment shall be
a minimum of ______ layers for roofs with slopes less than 4:12,
and conforming to ASTM D226. - ---Answers---2
After 3 years of installation, a steep-slope Energy Star roof
system must have a solar reflection GREATER than or equal to
- ---Answers---0.15 SRI
In the absence of manufacturer's recommendations, which
fastener is acceptable for all metal roofs? - ---Answers---
stainless steel
Ladder jack scaffolding shall not exceed _____ feet in height. -
---Answers---20
According to Florida Building Code, when installing skylights
on a single family residence, curbs may be omitted if the pitch
of the roof is a minimum of - ---Answers---3:12
According to Florida Building Code, what is the minimum
headlamp for a slate shingle roof with a 6:12 slope - ---
Answers---4"
According to SMACNA, in most cases, downspout size should
NOT be less than how many square inches in cross-section? -
---Answers---7 square inches
WITH QUESTIONS AND ACCURATE ANSWERS GRADED A+
A(n) ______ is a material that is sometimes used in the process
of seaming single-ply membranes to prepare the surfaces and
increase the shear strength of the field splice. - ---Answers--
-primer
What is the minimum thickness for an aluminum standing
seam roof with a 22-3/4" pan width? - ---Answers---.040"
What is the temperature range for Type III asphalt applied with
a mop application? - ---Answers---430 degrees F +/- 25
degrees F
When installing the base sheet of a built-up roof system over
plywood decking, nail all laps at________ centers. - ---
Answers---9"
When installing wood shakes or wood shingles, the units in the
starter course should be laid so that the butt ends extend
about ______ beyond the finish fascia board. - ---Answers---1-
1/2"
, According to the Florida Building Code, underlayment shall be
a minimum of ______ layers for roofs with slopes less than 4:12,
and conforming to ASTM D226. - ---Answers---2
After 3 years of installation, a steep-slope Energy Star roof
system must have a solar reflection GREATER than or equal to
- ---Answers---0.15 SRI
In the absence of manufacturer's recommendations, which
fastener is acceptable for all metal roofs? - ---Answers---
stainless steel
Ladder jack scaffolding shall not exceed _____ feet in height. -
---Answers---20
According to Florida Building Code, when installing skylights
on a single family residence, curbs may be omitted if the pitch
of the roof is a minimum of - ---Answers---3:12
According to Florida Building Code, what is the minimum
headlamp for a slate shingle roof with a 6:12 slope - ---
Answers---4"
According to SMACNA, in most cases, downspout size should
NOT be less than how many square inches in cross-section? -
---Answers---7 square inches
