API 570!! Questions and Answers correct
Code to follow when performing an internal inspection on pipe - answer"API 510"
Positive material identification (PMI) - answer"API 578"
Fitness for service - answer"API 579"
Risked based inspection (RBI) - answer"API 580"
Valve inspection and testing - answer"API 598"
Cathodic protection - answer"API 651"
Welding on in-service equipment containing the flammables - answer"API 2201"
NDE procedure guidelines - answer"ASME SECTION V"
Design code for fabrication of piping relief devices - answer"ASME SECTION 8"
Welder and weld procedure qualification - answer"ASME section 9"
NDE personnel qualification - answer"ASNT SNT-TC-1A"
API 570 scope - answer"AIRR
AIRR - answeralteration, inspection, repair, rerate
API 570 repair organization - answer"JOC - authorized jurisdiction, owner, contractor
API 570 Ai's employer - answer"JUIC - jurisdication, user, insurance company,
contractor
Determine corrosion rate for new service or change in service - answer"SOPI - Same or
similar service, Owners experience, Published data, inspect in three months
Primary responsibilities of API 570 authorized inspector - answer"TIE - testing
inspection examination
Define alteration - answer"Physical change"
Define repair - answer"Restore to suitable condition"
Define an imperfection that exceeds the acceptance criteria - answer"Defect"
, Define a discontinuity that may or may not exceed the acceptance criteria -
answer"Imperfection"
Risk based inspections primary factors - answer"Probability and consequence"
NDE number of CML's to obtain thickness readings during inspection -
answer"Representative"
NDE-CML that must be measured during the thickness inspection - answer"CML with
the earliest renewal date"
PRD's- How inspection intervals are determined - answer"Performance"
Factor used to classify pipe - answer"Consequence of failure"
Corrosion-method by which process leaks can lead to brittle failure - answer"Auto-
refrigeration"
Corrosion-cause for fatigue crack - answer"Cyclic stress"
Corrosion-factors that affect the creep rate - answer"Time, temp, stress
Corrosion-type of soil that is most corrosive - answer"Low resistivity"
Repairs-Number of new flange assemblies to be inspected during repairs and
alterations - answer"Representative"
SCC can develop at hot spots including where the heat tracing attaches to pipe in this
service - answer"Caustic"
Where dewpoint corrosion often occurs - answer"Overhead fractionation"
Potential for none or very few CMLS on circuit - answer"Olefin cold side, anhydrous
ammonia
Relatively uniform corrosion - answer"Sulfidation, sour water
Valves in this service should be inspected fatigue - answer"Cat Reformer"
Design-Mill tolerance for rolled and welded pipe - answer"-.010"
NDE- Maximum length of crack or incomplete fusion allowed on a new weld - answer"0"
Flanges- typical flange face finish - answer"125 - 250 micro inch"
Code to follow when performing an internal inspection on pipe - answer"API 510"
Positive material identification (PMI) - answer"API 578"
Fitness for service - answer"API 579"
Risked based inspection (RBI) - answer"API 580"
Valve inspection and testing - answer"API 598"
Cathodic protection - answer"API 651"
Welding on in-service equipment containing the flammables - answer"API 2201"
NDE procedure guidelines - answer"ASME SECTION V"
Design code for fabrication of piping relief devices - answer"ASME SECTION 8"
Welder and weld procedure qualification - answer"ASME section 9"
NDE personnel qualification - answer"ASNT SNT-TC-1A"
API 570 scope - answer"AIRR
AIRR - answeralteration, inspection, repair, rerate
API 570 repair organization - answer"JOC - authorized jurisdiction, owner, contractor
API 570 Ai's employer - answer"JUIC - jurisdication, user, insurance company,
contractor
Determine corrosion rate for new service or change in service - answer"SOPI - Same or
similar service, Owners experience, Published data, inspect in three months
Primary responsibilities of API 570 authorized inspector - answer"TIE - testing
inspection examination
Define alteration - answer"Physical change"
Define repair - answer"Restore to suitable condition"
Define an imperfection that exceeds the acceptance criteria - answer"Defect"
, Define a discontinuity that may or may not exceed the acceptance criteria -
answer"Imperfection"
Risk based inspections primary factors - answer"Probability and consequence"
NDE number of CML's to obtain thickness readings during inspection -
answer"Representative"
NDE-CML that must be measured during the thickness inspection - answer"CML with
the earliest renewal date"
PRD's- How inspection intervals are determined - answer"Performance"
Factor used to classify pipe - answer"Consequence of failure"
Corrosion-method by which process leaks can lead to brittle failure - answer"Auto-
refrigeration"
Corrosion-cause for fatigue crack - answer"Cyclic stress"
Corrosion-factors that affect the creep rate - answer"Time, temp, stress
Corrosion-type of soil that is most corrosive - answer"Low resistivity"
Repairs-Number of new flange assemblies to be inspected during repairs and
alterations - answer"Representative"
SCC can develop at hot spots including where the heat tracing attaches to pipe in this
service - answer"Caustic"
Where dewpoint corrosion often occurs - answer"Overhead fractionation"
Potential for none or very few CMLS on circuit - answer"Olefin cold side, anhydrous
ammonia
Relatively uniform corrosion - answer"Sulfidation, sour water
Valves in this service should be inspected fatigue - answer"Cat Reformer"
Design-Mill tolerance for rolled and welded pipe - answer"-.010"
NDE- Maximum length of crack or incomplete fusion allowed on a new weld - answer"0"
Flanges- typical flange face finish - answer"125 - 250 micro inch"
