Josh's IEC exam year #1 semester #1
for fasteners that are designed to be countersunk, the length is determined by the distance from the
end of the fastener to the _____________________________ - correct answer--the top of the head
a 1/4 - 28 x 3 !/2 machine screw has ________________ threads per inch. - correct answer--28
a 6-32 x 2 1/2 machine screw has a diameter of ___________ inches - correct answer--.138
Which of the following are wire connectors?
1. Split-bolt
2. Compression Connector
3. Mechanical Lug - correct answer--1, 2, & 3
look at questions 2, 5, 6 for the questions w/ pictures - correct answer--
As a general rule, the strength of a rope is reduced about _______________ when knot is tied - correct
answer--50%
Work can be preformed using power tools in wet locations if
_________________________________________________. - correct answer--the tool uses a low-
voltage insolation transformer.
Which of the following is NOT considered electrical hazard by OSHA. - correct answer--Power tool injury
, Extension ladders longer than _____ feet should not be used. - correct answer--60
A ladder that can be readily moved or carried describes a _________.
1. step ladder
2. extension ladder - correct answer--1 & 2
A type 2 ladder is rated to withstand a load of ___________ pounds. - correct answer--225 pounds
A worker who weighs 260 pounds and is wearing a 16 lb tool belt __________ exceeded the rating of a
Type 1A ladder. - correct answer--has NOT
If you are working with an extension ladder that has 15 rungs in each of the two sliding sections, this is a
_____________-foot extension ladder. - correct answer--30
If you are standing on the highest permitted step on a 12 foot step ladder, the top of your head will be
about ____________ feet above the floor. You are 6 feet tall. - correct answer--16
If you are standing on the highest permitted step on a 12 foot step ladder, you ________ required to use
fall protection equipment. - correct answer--are NOT
Moving carts or hand trucks over bumpy, rough terrain or up and down stairs may expose workers to
abrupt, jarring impacts which can cause shoulder and back pain. - correct answer--TRUE
While working in a hazardous area where the worker is exposed to serve impact hazards face shields are
required to be worn along with safety goggles or glasses. - correct answer--TRUE
Which of the following would best protect your eyes from the dust or other airborne particles?
for fasteners that are designed to be countersunk, the length is determined by the distance from the
end of the fastener to the _____________________________ - correct answer--the top of the head
a 1/4 - 28 x 3 !/2 machine screw has ________________ threads per inch. - correct answer--28
a 6-32 x 2 1/2 machine screw has a diameter of ___________ inches - correct answer--.138
Which of the following are wire connectors?
1. Split-bolt
2. Compression Connector
3. Mechanical Lug - correct answer--1, 2, & 3
look at questions 2, 5, 6 for the questions w/ pictures - correct answer--
As a general rule, the strength of a rope is reduced about _______________ when knot is tied - correct
answer--50%
Work can be preformed using power tools in wet locations if
_________________________________________________. - correct answer--the tool uses a low-
voltage insolation transformer.
Which of the following is NOT considered electrical hazard by OSHA. - correct answer--Power tool injury
, Extension ladders longer than _____ feet should not be used. - correct answer--60
A ladder that can be readily moved or carried describes a _________.
1. step ladder
2. extension ladder - correct answer--1 & 2
A type 2 ladder is rated to withstand a load of ___________ pounds. - correct answer--225 pounds
A worker who weighs 260 pounds and is wearing a 16 lb tool belt __________ exceeded the rating of a
Type 1A ladder. - correct answer--has NOT
If you are working with an extension ladder that has 15 rungs in each of the two sliding sections, this is a
_____________-foot extension ladder. - correct answer--30
If you are standing on the highest permitted step on a 12 foot step ladder, the top of your head will be
about ____________ feet above the floor. You are 6 feet tall. - correct answer--16
If you are standing on the highest permitted step on a 12 foot step ladder, you ________ required to use
fall protection equipment. - correct answer--are NOT
Moving carts or hand trucks over bumpy, rough terrain or up and down stairs may expose workers to
abrupt, jarring impacts which can cause shoulder and back pain. - correct answer--TRUE
While working in a hazardous area where the worker is exposed to serve impact hazards face shields are
required to be worn along with safety goggles or glasses. - correct answer--TRUE
Which of the following would best protect your eyes from the dust or other airborne particles?
