Forklift Certification Test
FORKLIFT CERTIFICATION TEST INCLUDES 250 ACCURATE AND
VERIFIED QUESTIONS COVERING OSHA SAFETY STANDARDS, FORKLIFT
OPERATION, LOAD HANDLING, INSPECTION PROCEDURES, HAZARD
RECOGNITION, AND WORKPLACE SAFETY PROTOCOLS
When approaching an intersection, you should
a) Always approach slowly, keeping an eye out for pedestrians and other trucks.
b) Come to a full stop, once each traffic lane is fully visible
c) Check for oncoming traffic, then sound the horn, and proceed with caution.
D) All of the above - ANSWER-All of the above
When traveling make sure the mast is
a) Raised about 24"
) Lowered with forks about 4-6" above the work surface
c) Tilted forward
d) None of the above - ANSWER-Lowered with forks about 4-6" above the work surface
When traveling up or down a ramp or incline with a loaded lift truck, the load is to be kept
a) Downgrade
b) Raised at least 24"
C) Upgrade
d) Either up or downgrade - ANSWER-C) Upgrade
When traveling up or down a ramp or incline without a load, the counterweight is to be kept
a) Downgrade
b) Raised at least 24"
1|Page
, Forklift Certification Test
C) Upgrade
d) Either up or downgrade - ANSWER-C) upgrade
lift trucks should not turn on an incline.
a) Class I
b) Class II
c) Class Ill
d) Class IV
e) Class V
F) all of the above - ANSWER-F) all of the above
An approved safety platform must be equipped with
a) Safety railings
b) Solid floor
c) Screen or bars separating the platform and the moving parts of the mast
D) all of the above - ANSWER-D) all of the above
When parking a lift truck,
a) Stop the lift truck and apply the parking brake
b) Fully lower the forks or carriage and tilt the mast forward
c) Put the directional control in neutral.
d) Turn the key to the off position and remove the key.
e) If the truck is powered by LPG fuel, make sure to shut off the flow of gas at the fuel tank
f) All of the above - ANSWER-f) All of the above
The primary responsibility of the operator is to —
2|Page
, Forklift Certification Test
a) Use the powered industrial truck safely and properly
b) Make sure all loads are in place at the end of the shift
c) Move as much material as possible in order to increase profits.
d) All of the above - ANSWER-a) Use the powered industrial truck safely and properly
OSHA requires that operators of powered industrial trucks be
a) Trained and evaluated
b) At least 21 and have a current drivers license
c) Experienced
d) All of the above - ANSWER-a) Trained and evaluated
You should never attempt to operate a powered industrial truck unless
A) You have been trained, evaluated and certified by your ernployer, or in the process of being
trained, with a, trainer observing
b) No one else is around, the load needs to be moved and you have operated a lift truck before
on your previous job
c) The regular operator says that it is OK - ANSWER-A. You should never attempt to operate a
powered industrial truck unless a You have been trained, evaluated and certified by your
ernployer, or in the process of being trained, with a, trainer observing
can cause the stability of a lift truck to change.
A.Turning
b) Accelerating
c) Stopping
d) Operating on an incline
g) All of the above - ANSWER-G. All of the above
3|Page
, Forklift Certification Test
On the data plate you will find
a) Truck model
b) Serial number
c) Lifting capacity
A) All of the above - ANSWER-A) All of the above
A forklift's fulcrum is at
A) Center line of its front wheels.
b) Between the front and rear wheels
c) At the front edge of its carriage.
d) None of the above - ANSWER-A) center line of its front wheel
The stability of a lift truck is affected by several factors such as
a) Load weight
b) Load size
c) Load type
d) Height the load will be lifted
All of the above - ANSWER-All of the above
If a lift truck fails any part of the inspection you should
a) Tag it
b) Remove the key
c) Take it out of service and report the problem to your supervisor )
D) All of the above - ANSWER-D) All of the above
4|Page
FORKLIFT CERTIFICATION TEST INCLUDES 250 ACCURATE AND
VERIFIED QUESTIONS COVERING OSHA SAFETY STANDARDS, FORKLIFT
OPERATION, LOAD HANDLING, INSPECTION PROCEDURES, HAZARD
RECOGNITION, AND WORKPLACE SAFETY PROTOCOLS
When approaching an intersection, you should
a) Always approach slowly, keeping an eye out for pedestrians and other trucks.
b) Come to a full stop, once each traffic lane is fully visible
c) Check for oncoming traffic, then sound the horn, and proceed with caution.
D) All of the above - ANSWER-All of the above
When traveling make sure the mast is
a) Raised about 24"
) Lowered with forks about 4-6" above the work surface
c) Tilted forward
d) None of the above - ANSWER-Lowered with forks about 4-6" above the work surface
When traveling up or down a ramp or incline with a loaded lift truck, the load is to be kept
a) Downgrade
b) Raised at least 24"
C) Upgrade
d) Either up or downgrade - ANSWER-C) Upgrade
When traveling up or down a ramp or incline without a load, the counterweight is to be kept
a) Downgrade
b) Raised at least 24"
1|Page
, Forklift Certification Test
C) Upgrade
d) Either up or downgrade - ANSWER-C) upgrade
lift trucks should not turn on an incline.
a) Class I
b) Class II
c) Class Ill
d) Class IV
e) Class V
F) all of the above - ANSWER-F) all of the above
An approved safety platform must be equipped with
a) Safety railings
b) Solid floor
c) Screen or bars separating the platform and the moving parts of the mast
D) all of the above - ANSWER-D) all of the above
When parking a lift truck,
a) Stop the lift truck and apply the parking brake
b) Fully lower the forks or carriage and tilt the mast forward
c) Put the directional control in neutral.
d) Turn the key to the off position and remove the key.
e) If the truck is powered by LPG fuel, make sure to shut off the flow of gas at the fuel tank
f) All of the above - ANSWER-f) All of the above
The primary responsibility of the operator is to —
2|Page
, Forklift Certification Test
a) Use the powered industrial truck safely and properly
b) Make sure all loads are in place at the end of the shift
c) Move as much material as possible in order to increase profits.
d) All of the above - ANSWER-a) Use the powered industrial truck safely and properly
OSHA requires that operators of powered industrial trucks be
a) Trained and evaluated
b) At least 21 and have a current drivers license
c) Experienced
d) All of the above - ANSWER-a) Trained and evaluated
You should never attempt to operate a powered industrial truck unless
A) You have been trained, evaluated and certified by your ernployer, or in the process of being
trained, with a, trainer observing
b) No one else is around, the load needs to be moved and you have operated a lift truck before
on your previous job
c) The regular operator says that it is OK - ANSWER-A. You should never attempt to operate a
powered industrial truck unless a You have been trained, evaluated and certified by your
ernployer, or in the process of being trained, with a, trainer observing
can cause the stability of a lift truck to change.
A.Turning
b) Accelerating
c) Stopping
d) Operating on an incline
g) All of the above - ANSWER-G. All of the above
3|Page
, Forklift Certification Test
On the data plate you will find
a) Truck model
b) Serial number
c) Lifting capacity
A) All of the above - ANSWER-A) All of the above
A forklift's fulcrum is at
A) Center line of its front wheels.
b) Between the front and rear wheels
c) At the front edge of its carriage.
d) None of the above - ANSWER-A) center line of its front wheel
The stability of a lift truck is affected by several factors such as
a) Load weight
b) Load size
c) Load type
d) Height the load will be lifted
All of the above - ANSWER-All of the above
If a lift truck fails any part of the inspection you should
a) Tag it
b) Remove the key
c) Take it out of service and report the problem to your supervisor )
D) All of the above - ANSWER-D) All of the above
4|Page
