Science Engineering Chemical Engineering
NACE CIP 1 CBT EXAM PRACTICE QUESTIONS
Save
Students also studied
Flashcard sets Study guides
NACE CIP 1 CBT Exam (Quizzes and ... NACE CIP 1 CBT EXAM PRACTICE Q... ICC Sample Exam Q
203 terms 189 terms Teacher 21 terms
Marqus2019 Preview jwetzel43432 Preview oscar_david87
Practice questions for this set
Learn 1 /7 Study with Learn
Dew point is the temperature at condensation occurs.
which
You are the NACE Inspector on Document the problem and advise the Contractor and Owner's
a tank lining project where a representative.
50% solids epoxy tank lining is
being applied. After application
of the 19 coat you notice small
blisters in some areas of the
applied lining. Your FIRST
preferred course of action is to:
If a contractor is using a poorly blotter test for the presence of oil and water.
maintained compressor to
supply air for abrasive blast
cleaning and conventional
airspray, the coating inspector
should perform a
Upon arrival of coating observe and document the amount of material and batch
materials, the inspector should numbers.
, a measure of the amount of moisture in the air compared to
Relative humidity is
saturation level.
Galvanic corrosion occurs on Metal
which of the following
substrates?
When applying Thermal Spray SSPC-CS 23.00/AWS C2.23/NACE No. 12
Coatings the specification is
most likely to reference:
What is the minimum 2.5 cm (1 inch)
recommended distance away
from an edge that an inspector
should take a measurement with
a dial type magnetic pull off Dry
Film Thickness(DFT) gauge?
Polymerization is the process Monomers joining together.
of?
An exposed area of the Holiday
substrate or previous coat of a
conductive material, often
caused by poor application
technique is called:
a fine crack in the surface of a coating that rarely reaches the
Checking is:
substrate.
Inspection documentation is Owners use the documentation for a variety of purposes.
important because:
An Inspectors personal log No comments regarding the application team.
book should contain:
You have just received your Review the NACE Attestation prior to making a decision.
NACE CIP Level 1 certification
when you are asked to supervise
a team of uncertified field
pipeline inspectors. Your FIRST
preferred course of action is to:
Good record can provide How the item was coated.
maintenance departments with
detailed information about ALL
of the following EXCEPT:
Non Conformance Reports are When the Inspector and Contractor deem it to be significant non
completed by the Inspector: conforming item.
The initial steel condition is The Inspector may have to reject the steel.
important to the NACE
Inspector because:
The form of corrosion that has Galvanic Corrosion
the largest potential for
unexpected catastrophic failure
is:
What is used to determine Profilometer
compressed air cleanliness?
NACE CIP 1 CBT EXAM PRACTICE QUESTIONS
Save
Students also studied
Flashcard sets Study guides
NACE CIP 1 CBT Exam (Quizzes and ... NACE CIP 1 CBT EXAM PRACTICE Q... ICC Sample Exam Q
203 terms 189 terms Teacher 21 terms
Marqus2019 Preview jwetzel43432 Preview oscar_david87
Practice questions for this set
Learn 1 /7 Study with Learn
Dew point is the temperature at condensation occurs.
which
You are the NACE Inspector on Document the problem and advise the Contractor and Owner's
a tank lining project where a representative.
50% solids epoxy tank lining is
being applied. After application
of the 19 coat you notice small
blisters in some areas of the
applied lining. Your FIRST
preferred course of action is to:
If a contractor is using a poorly blotter test for the presence of oil and water.
maintained compressor to
supply air for abrasive blast
cleaning and conventional
airspray, the coating inspector
should perform a
Upon arrival of coating observe and document the amount of material and batch
materials, the inspector should numbers.
, a measure of the amount of moisture in the air compared to
Relative humidity is
saturation level.
Galvanic corrosion occurs on Metal
which of the following
substrates?
When applying Thermal Spray SSPC-CS 23.00/AWS C2.23/NACE No. 12
Coatings the specification is
most likely to reference:
What is the minimum 2.5 cm (1 inch)
recommended distance away
from an edge that an inspector
should take a measurement with
a dial type magnetic pull off Dry
Film Thickness(DFT) gauge?
Polymerization is the process Monomers joining together.
of?
An exposed area of the Holiday
substrate or previous coat of a
conductive material, often
caused by poor application
technique is called:
a fine crack in the surface of a coating that rarely reaches the
Checking is:
substrate.
Inspection documentation is Owners use the documentation for a variety of purposes.
important because:
An Inspectors personal log No comments regarding the application team.
book should contain:
You have just received your Review the NACE Attestation prior to making a decision.
NACE CIP Level 1 certification
when you are asked to supervise
a team of uncertified field
pipeline inspectors. Your FIRST
preferred course of action is to:
Good record can provide How the item was coated.
maintenance departments with
detailed information about ALL
of the following EXCEPT:
Non Conformance Reports are When the Inspector and Contractor deem it to be significant non
completed by the Inspector: conforming item.
The initial steel condition is The Inspector may have to reject the steel.
important to the NACE
Inspector because:
The form of corrosion that has Galvanic Corrosion
the largest potential for
unexpected catastrophic failure
is:
What is used to determine Profilometer
compressed air cleanliness?
