UP Return to Work Study Guide With Complete Answers | Updated

UP Return to Work Study Guide With Complete Answers | Updated /."Stowed" requires (2.21/Glossary) - Answer-Having personal electronic devices powered off and out of sight. Devices in pockets are not stowed. /.Your 5,681 ton train goes into emergency at a speed of 21mph. No unusual slack action was felt and the brake pipe pressure was immediately restored after stopping. Will you be required to walk the train? 6.23 - Answer-No, you are relieved of having to check it due to the speed being over 20mph, no unusual slack action was felt, and the brake pipe pressure was immediately restored after stopping. /.What is your crew's responsibility to the trian dispatcher regarding an emergency application of the air brakes? 6.31 - Answer-Unclear. Listed rule does not match description. /.Reverse Movement (Glossary) - Answer-Movement in the opposite direction of authorized movement /.When moving on the main track or siding, are you required to ring the bell continuously while passing standing equipment on the adjacent track? 5.8.1 - Answer-Yes. /.What is required when delayed within a block in CTC limits when PTC is not in effect? 9.9 - Answer-Proceed prepared to stop at the next signal until the next signal is visible and that signal displays a proceed indication. /.What actions are required before fouling or crossing a track? (81.2.1) - Answer-Look in both directions Ensure no movement is closely approaching Look for conditions that could interfere with footing /.How may your train be authorized by a stop indication at a manual interlocking? 9.12.2 - Answer-Contact control operator who will give permission when it is known that the route is properly lined and no conflicting movement is occupying or authorized to enter the track between that signal and the next absolute signal. /.Pounds of brake pipe pressure that must be present at the rear of the train before beginning an Initial Terminal Air Brake Test (Class 1) 30.3/30.10.1 - Answer-90 /.while flagging a signal at a manual interlocking, the dispatcher calls and tells you to pick up a repaired bad order car off the next siding. How will you answer the dispatcher's request? Your train is operating at restricted speed. 1.47.1 - Answer-Tell dispatcher you are in a cab red zone and cannot respond. /.Are you required to obtain Red Zone Protection before releasing the hand brakes on your train while the car department has your train blue flagged? 81.5.4/5.13 - Answer-You are not allowed to release the hand brakes on your train while the train is blue flagged unless directed by the employee who placed the blue flag or the EIC of the employees working on the blue flagged train. /.When operating west of El Paso, where must you place an empty multiplatform spine car in your manifest train to comply with train make-up restrictions? SSI Item 5-B - Answer-Behind a car with no more than 4500 tons /.Before cutting away from the rear portion of your train with a set out, what securement procedure would you use? 32.1.3/32.1/32.1.1 - Answer-Tie sufficient hand brakes Make a 20psi brake pipe reduction Close angle cock on Locomotive after brake pipe exhaust ceases Leave angle cock open on the portion left standing to ensure air is not bottled /.The dispatcher would like you to handle the switch for a pick-up off a controlled siding within CTC. Descrive how this switching move could be made using the switch in hand position. 9.13.2 - Answer-Job brief with dispatcher on moves to be made, receive authority to enter the control point, and receive permission to place the switch in hand operation. Unlock switch lock, place selector lever in hand position. Operate hand throw lever until switch points are seen to move, even if it is already lined for intended route. Line switch for your route. Do not return power to switch until final movement has been made over the switch. /.If it is necessary to work between a yard track and the adjacent CTC controlled siding, will you be required to obtain Track Breach Protection? SSI Item 12 - Answer-Yes. /.After doubling a solid block of cars to your train, what air brake test(s) and inspections will be necessary before departing? 30.7.1 & Glossary - Answer-Class III Application and Release of brakes. /.What is required before an employee may choose to ride on moving equipment? 81.7 - Answer-Other ways to complete task without needing to ride on equipment Weather conditions Car design and configuration that may make it unsuitable to ride Your physical limitations Potential slack action Applicable Operating and Safety Rules /.After completing a train inspection for a hot journal, how may the train be shoved back to pick up a crew member? 6.6 - Answer-Movement will not exceed limits of train and trains length. Will not enter or foul public crossing unless proving warning per rule 6.32.1. Cannot be made into or within yard limits, restricted limits, interlocking limits, drawbridges, rr crossings at grade, or track bulletin form b limits. /.If you choose to ride a tank car equipped with one vertical handhold when pulling out of a track, how should you do so? 81.7 - Answer-On the trailing end of the car and outside the gauge of the track with both feet planted /.While passing a (#) type detector, it transmits the following message: UP detector, MP 538.1 on Track 2. Stop your train, stop your train, first hotbox, axle 372 on north side. Detector out." When will the engineer be required to stop the train in response to the hotbox detector actuation? SSI Item 13 - Answer-Stop the train immediately and inspect for dragging equipment. /.How can you determine a RCL Zone is active? 6.7 - Answer-Thorugh the RCO, other authorized employee, or special instructions. /.Would you be able to pull a train by to the indicated axle location to inspect for the hot journal? SSI Item 13 - Answer-Only if not a key train, not on rails with concrete ties , indicated axel will not pass over a switch, not the 2nd got box detector on the same car, and visual observation indicates no smoke, flame, or excessive dust. Train just also not require excessive power to continue movement. /.What protection is required before fouling bowl track(s) during humping operations? 7.13 - Answer-Protection from the employee in charge of the Hump /.A train inspection requires you to work between main tracks 1 and 2. Will you be required to obtain any protection before doing so? SSI Item 12 - Answer-Yes. /.When requesting protection before working in bowl track(s) during humping operations, how many tracks must be protected? (Locked up) 7.13 - Answer-It varies, any switch that leads to that track must be locked against movement to the protected bowl track /.How should you inspect for an overheated journal? SSI Item 13 - Answer-Retaining valve in exhaust position, hand brake fully released, brakes are not sticking, truck bolster not broken, brake rigging/lading not down or dragging, wheels are not broken or improperly positioned on the rail, and lading has not dropped down through container floors or cross members of multi unit/well cars. /.If the person disappears who is giving the signal to back or shove a train, engine, or car, or the light being used disappears, employees must: 5.3.3 & 6.5 - Answer-Stop within half the specified distance, unless able to make radio contact. /.What must be done before lining a switch? 82.3 - Answer-LISOP Look, inspect, sweep, operate switch and point at correct switch points