MSSC - Quality Practices and
Measurement FINAL EXAM STUDY GUIDE
2025/2026 COMPLETE QUESTIONS BANK AND
CORRECT DETAILED ANSWERS WITH
RATIONALES || 100% GUARANTEED PASS
<LATEST VERSION>
1. Which type of feature is parallel to the surface being dimensioned? -
ANSWER ✓ Dimension line
2. The three standard views of an object are __________. - ANSWER ✓ Top,
front, right side
3. Which type of lines are used to show the counterbored hole in the part? -
ANSWER ✓ Hidden lines
4. The number of views in a drawing __________. - ANSWER ✓ Is the fewest
number that shows all of the features and dimensions
5. New product design teams should perform a(n) __________ as early in the
design process as possible. - ANSWER ✓ Design Failure Mode and Effect
Analysis
6. Companies typically require that __________ as part of their shop safety
rules. - ANSWER ✓ Safety glasses be worn
7. The safety of personnel and the equipment as well as the performance of the
equipment are the key points to keep in mind when making a decision to
__________. - ANSWER ✓ Run to failure or shut down to fix
,8. Predicting the percentage of parts that will fall within certain measurements
if the data is distributed normally is done by calculating the __________. -
ANSWER ✓ Standard deviation
9. A 100% inspection of a new product revealed that a run of 200 parts resulted
in several parts being rejected. If the rejection rate was 3%. How many bad
parts were created? - ANSWER ✓ 6
10.If 200 parts are sampled from every 3000 produced, what is the sampling
rate? - ANSWER ✓ 6.7 percent
11.A __________ is a graphic method to show how the data is distributed
across the range of values. - ANSWER ✓ Histogram
12.Statistical process control (SPC) is used to __________. - ANSWER ✓
Determine when a process is going to produce bad parts before it actually
does
13.If the histogram of a process is not bell-shaped, then the process is
__________. - ANSWER ✓ Not stable
14.Two types of variation are __________. - ANSWER ✓ Common cause and
special cause
15.Once the Cpk of a process is determined, it can predict the __________ of a
product as long as the process __________. - ANSWER ✓ Quality, remains
in control
16.Production departments develop a quality history database by __________. -
ANSWER ✓ Recording inspection data
17.A histogram is one type of tool that can be used to __________. - ANSWER
✓ Measure process control
18.A bell-shaped curve that results from a large group of measurements is the
basic concept of __________. - ANSWER ✓ Central tendency
,19.To save money using SPC, a factory determines if there is a(n) __________
in a process. - ANSWER ✓ Special cause variation
20.When constructing a histogram, no value should ever fall on a(n)
__________. - ANSWER ✓ Boundary
21.Workers perform __________ to control product quality, develop SPC
charts, and determine if parts meet specifications. - ANSWER ✓ Inspections
22.Parts are inspected __________ to make sure the typical characteristics of a
produced parts are found. - ANSWER ✓ Randomly
23.In
manufacturing, a blueprint is also called what? - ANSWER ✓ A technical
drawing
24.An isometric drawing is a type of ___________. - ANSWER ✓ Pictorial
drawing
25.Which of the following is NOT used in the glass box method? - ANSWER
✓ Rotate object in glass box.
26.Which of these requires a computer? - ANSWER ✓ CAD
27.The dimensions of raw material supplied by metal suppliers are described by
the __________. - ANSWER ✓ stock size
28.The three standard views of an object are __________. - ANSWER ✓ Top,
front, right side
29.Engineers sometimes use a ________ to measure angles on a drawing. -
ANSWER ✓ protractor
30.The holes to be drilled in the part are represented by - ANSWER ✓ Dashed
lines
31.What is the order of precedence of lines in a drawing? - ANSWER ✓
Object, hidden, center
, 32.The number of views in a drawing ________. - ANSWER ✓ Is the fewest
number that shows all of the features and dimensions.
33.There are 60 minutes of arc in one _______. - ANSWER ✓ Degree
34.Dimensions are used to specify the __________ and location of the features
of an object. - ANSWER ✓ Size
35.__________ should be validated and approved to ensure accuracy. -
ANSWER ✓ Standard operating procedures
36.The number of defects produced is a measure of __________. - ANSWER ✓
The effectiveness of a quality assurance system
37.Of the four roles of management, controlling covers which of the following
actions: - ANSWER ✓ Monitoring actual to standard work performance
38.Kaizen, Kanban, and 5S are just a few of many elements used in a(n)
__________ operation. - ANSWER ✓ Just In Time (JIT)
39.Defect prevention is the __________ of the four types of quality costs. -
ANSWER ✓ Most cost effective
40.Joseph M. Juran, W. Edwards Deming, and C. Phillip Crosby contributed to
the various approaches of __________. - ANSWER ✓ TQM, Total Quality
Management
41.To reduce variation, minimize defects, and to shorten cycle time are
considered __________ goals. - ANSWER ✓ Quality
42.A worker should __________ any time the worker notices a minor quality
problem that is not critical to product function or performance. - ANSWER
✓ Notify the supervisor to determine the correct action to take
43.Greater variations in a process may occur when __________. - ANSWER ✓
Unapproved process adjustments are performed
Measurement FINAL EXAM STUDY GUIDE
2025/2026 COMPLETE QUESTIONS BANK AND
CORRECT DETAILED ANSWERS WITH
RATIONALES || 100% GUARANTEED PASS
<LATEST VERSION>
1. Which type of feature is parallel to the surface being dimensioned? -
ANSWER ✓ Dimension line
2. The three standard views of an object are __________. - ANSWER ✓ Top,
front, right side
3. Which type of lines are used to show the counterbored hole in the part? -
ANSWER ✓ Hidden lines
4. The number of views in a drawing __________. - ANSWER ✓ Is the fewest
number that shows all of the features and dimensions
5. New product design teams should perform a(n) __________ as early in the
design process as possible. - ANSWER ✓ Design Failure Mode and Effect
Analysis
6. Companies typically require that __________ as part of their shop safety
rules. - ANSWER ✓ Safety glasses be worn
7. The safety of personnel and the equipment as well as the performance of the
equipment are the key points to keep in mind when making a decision to
__________. - ANSWER ✓ Run to failure or shut down to fix
,8. Predicting the percentage of parts that will fall within certain measurements
if the data is distributed normally is done by calculating the __________. -
ANSWER ✓ Standard deviation
9. A 100% inspection of a new product revealed that a run of 200 parts resulted
in several parts being rejected. If the rejection rate was 3%. How many bad
parts were created? - ANSWER ✓ 6
10.If 200 parts are sampled from every 3000 produced, what is the sampling
rate? - ANSWER ✓ 6.7 percent
11.A __________ is a graphic method to show how the data is distributed
across the range of values. - ANSWER ✓ Histogram
12.Statistical process control (SPC) is used to __________. - ANSWER ✓
Determine when a process is going to produce bad parts before it actually
does
13.If the histogram of a process is not bell-shaped, then the process is
__________. - ANSWER ✓ Not stable
14.Two types of variation are __________. - ANSWER ✓ Common cause and
special cause
15.Once the Cpk of a process is determined, it can predict the __________ of a
product as long as the process __________. - ANSWER ✓ Quality, remains
in control
16.Production departments develop a quality history database by __________. -
ANSWER ✓ Recording inspection data
17.A histogram is one type of tool that can be used to __________. - ANSWER
✓ Measure process control
18.A bell-shaped curve that results from a large group of measurements is the
basic concept of __________. - ANSWER ✓ Central tendency
,19.To save money using SPC, a factory determines if there is a(n) __________
in a process. - ANSWER ✓ Special cause variation
20.When constructing a histogram, no value should ever fall on a(n)
__________. - ANSWER ✓ Boundary
21.Workers perform __________ to control product quality, develop SPC
charts, and determine if parts meet specifications. - ANSWER ✓ Inspections
22.Parts are inspected __________ to make sure the typical characteristics of a
produced parts are found. - ANSWER ✓ Randomly
23.In
manufacturing, a blueprint is also called what? - ANSWER ✓ A technical
drawing
24.An isometric drawing is a type of ___________. - ANSWER ✓ Pictorial
drawing
25.Which of the following is NOT used in the glass box method? - ANSWER
✓ Rotate object in glass box.
26.Which of these requires a computer? - ANSWER ✓ CAD
27.The dimensions of raw material supplied by metal suppliers are described by
the __________. - ANSWER ✓ stock size
28.The three standard views of an object are __________. - ANSWER ✓ Top,
front, right side
29.Engineers sometimes use a ________ to measure angles on a drawing. -
ANSWER ✓ protractor
30.The holes to be drilled in the part are represented by - ANSWER ✓ Dashed
lines
31.What is the order of precedence of lines in a drawing? - ANSWER ✓
Object, hidden, center
, 32.The number of views in a drawing ________. - ANSWER ✓ Is the fewest
number that shows all of the features and dimensions.
33.There are 60 minutes of arc in one _______. - ANSWER ✓ Degree
34.Dimensions are used to specify the __________ and location of the features
of an object. - ANSWER ✓ Size
35.__________ should be validated and approved to ensure accuracy. -
ANSWER ✓ Standard operating procedures
36.The number of defects produced is a measure of __________. - ANSWER ✓
The effectiveness of a quality assurance system
37.Of the four roles of management, controlling covers which of the following
actions: - ANSWER ✓ Monitoring actual to standard work performance
38.Kaizen, Kanban, and 5S are just a few of many elements used in a(n)
__________ operation. - ANSWER ✓ Just In Time (JIT)
39.Defect prevention is the __________ of the four types of quality costs. -
ANSWER ✓ Most cost effective
40.Joseph M. Juran, W. Edwards Deming, and C. Phillip Crosby contributed to
the various approaches of __________. - ANSWER ✓ TQM, Total Quality
Management
41.To reduce variation, minimize defects, and to shorten cycle time are
considered __________ goals. - ANSWER ✓ Quality
42.A worker should __________ any time the worker notices a minor quality
problem that is not critical to product function or performance. - ANSWER
✓ Notify the supervisor to determine the correct action to take
43.Greater variations in a process may occur when __________. - ANSWER ✓
Unapproved process adjustments are performed
