1|Page
CSWA S EXAM 2025/2026 BANK COMPLETE
QUESTIONS AND ANSWERS ACCURATE
ACTUAL EXAM WITH FREQUENTLY
TESTED QUESTIONS AND STUDY GUIDE /
EXPERT VERIFIED FOR GUARANTEED
PASS/ALREADY GRADED A+
Linear static analysis assumes that the relationship between loads and the
induced response is: .....answer.....Linear
In SOLIDWORKS Simulation, the Factor of Safety (FOS) calculations are
based on which of the following failure criteria? .....answer.....Maximum von
Mises Stress
The Yield point is the point where the material begins to deform at a faster
rate than at the elastic limit. The material behaves ______ in the Plastic
Range. .....answer.....non-linearly
What are the Degrees of Freedom (DOFs) restrained for a Solid?
.....answer.....3 Translations
,2|Page
What are the Degrees of Freedom (DOFs) restrained for Shells and Beams?
.....answer.....3 Translations and 3 Rotations
A Beam element has _____ nodes (one at each end with ______ degrees of
freedom per node plus ______ node to define the orientation of the beam
cross section. .....answer.....3, 6, 1
A Truss element has ______ nodes with ______ translational degrees of
freedom per node. .....answer.....2, 3
How does SOLIDWORKS Simulation automatically treat a Sheet metal part
with uniform thickness? .....answer.....Shell
What is the Modulus for Elasticity? .....answer.....The slope of the Stress-
Strain curve in its linear section
What is Stress? .....answer.....A measure of the average amount of force
exerted per unit area
, 3|Page
Which of the following assumptions are true for static analysis in
SOLIDWORKS Simulation with small displacements? .....answer.....Inertia
effects are negligible and loads are applied slowly
What is Yield Stress .....answer.....The stress level beyond which the material
becomes plastic
A high-quality shell element has ________ nodes .....answer.....6
Stress σ is proportional to: .....answer.....Strain
The Elastic Modulus (Young's Modulus) is the slope defined as ______ by
_______ .....answer.....stress, strain
In general, the finer the mesh the better the accuracy of the results
.....answer.....True
Surface models can only be meshed with _____ elements. .....answer.....Shell
The shell mesh is generated on the surface (located at the mid-surface of the
shell) .....answer.....True
CSWA S EXAM 2025/2026 BANK COMPLETE
QUESTIONS AND ANSWERS ACCURATE
ACTUAL EXAM WITH FREQUENTLY
TESTED QUESTIONS AND STUDY GUIDE /
EXPERT VERIFIED FOR GUARANTEED
PASS/ALREADY GRADED A+
Linear static analysis assumes that the relationship between loads and the
induced response is: .....answer.....Linear
In SOLIDWORKS Simulation, the Factor of Safety (FOS) calculations are
based on which of the following failure criteria? .....answer.....Maximum von
Mises Stress
The Yield point is the point where the material begins to deform at a faster
rate than at the elastic limit. The material behaves ______ in the Plastic
Range. .....answer.....non-linearly
What are the Degrees of Freedom (DOFs) restrained for a Solid?
.....answer.....3 Translations
,2|Page
What are the Degrees of Freedom (DOFs) restrained for Shells and Beams?
.....answer.....3 Translations and 3 Rotations
A Beam element has _____ nodes (one at each end with ______ degrees of
freedom per node plus ______ node to define the orientation of the beam
cross section. .....answer.....3, 6, 1
A Truss element has ______ nodes with ______ translational degrees of
freedom per node. .....answer.....2, 3
How does SOLIDWORKS Simulation automatically treat a Sheet metal part
with uniform thickness? .....answer.....Shell
What is the Modulus for Elasticity? .....answer.....The slope of the Stress-
Strain curve in its linear section
What is Stress? .....answer.....A measure of the average amount of force
exerted per unit area
, 3|Page
Which of the following assumptions are true for static analysis in
SOLIDWORKS Simulation with small displacements? .....answer.....Inertia
effects are negligible and loads are applied slowly
What is Yield Stress .....answer.....The stress level beyond which the material
becomes plastic
A high-quality shell element has ________ nodes .....answer.....6
Stress σ is proportional to: .....answer.....Strain
The Elastic Modulus (Young's Modulus) is the slope defined as ______ by
_______ .....answer.....stress, strain
In general, the finer the mesh the better the accuracy of the results
.....answer.....True
Surface models can only be meshed with _____ elements. .....answer.....Shell
The shell mesh is generated on the surface (located at the mid-surface of the
shell) .....answer.....True
