Scaffold Nccer Part 1
The primary governing body over the scaffold and regulations is - (correct Answer) - OSHA.
Scaffoids over ______ft need to be designed by an engeneer - (correct Answer) - 125
When installing tarps or plastics ob a scaffold _____ _____ is to be considered - (correct Answer) - Wfad
loas
The circumference (distance around)a vessel that is 40ft diameter is - (correct Answer) - 125 ft
(the formula for figuring out diameter is (3.14 x diameter))
Tape or wrapping should not be used on the handle of a hammer because it may - (correct Answer) -
Hide defects
Breaking material bends shouldnoy be done with the - (correct Answer) - Hammer
Rest decks must be installed on ladders in excess ___ ft in height. - (correct Answer) - 35 ft
Damaged materials shouid not be - (correct Answer) - repaired, repiecced or taken out service
Screwed jacks can be raised a maximum of - (correct Answer) - 12 inches
Scaffold pianks shouid be secured to the piatform using - (correct Answer) - #9 wire
A bosins chair is a ______ ______ suspended scaffold - (correct Answer) - Single point
A bosins chair is a ____ ____ scaffold - (correct Answer) - Light duty
The safety equipment required when using a hammer is - (correct Answer) - Safety glasses
14. A light duty scafiold is rated at _____ lb per square foot of decking. - (correct Answer) - 25 lb
A medium duty scaffold is rated at ___ pounds per square foot of decking. - (correct Answer) - 50 pounds
A heavy duty scaffoid is rated at ___ pounds per square foot of decking. - (correct Answer) - 75 pounds
Right angle clamps should be tightened at ___ lb torque. - (correct Answer) - 45 lb
When using a scaffold wrench you should always _____ _____ from your body. - (correct Answer) - Push
away
Snap hooks and d rings on safety harness are rated to hold ____. - (correct Answer) - 5000 lb
- (correct Answer) - Screw jacks (laying lacks)
- (correct Answer) - Torpedo level
- (correct Answer) - Scaffold post
The primary governing body over the scaffold and regulations is - (correct Answer) - OSHA.
Scaffoids over ______ft need to be designed by an engeneer - (correct Answer) - 125
When installing tarps or plastics ob a scaffold _____ _____ is to be considered - (correct Answer) - Wfad
loas
The circumference (distance around)a vessel that is 40ft diameter is - (correct Answer) - 125 ft
(the formula for figuring out diameter is (3.14 x diameter))
Tape or wrapping should not be used on the handle of a hammer because it may - (correct Answer) -
Hide defects
Breaking material bends shouldnoy be done with the - (correct Answer) - Hammer
Rest decks must be installed on ladders in excess ___ ft in height. - (correct Answer) - 35 ft
Damaged materials shouid not be - (correct Answer) - repaired, repiecced or taken out service
Screwed jacks can be raised a maximum of - (correct Answer) - 12 inches
Scaffold pianks shouid be secured to the piatform using - (correct Answer) - #9 wire
A bosins chair is a ______ ______ suspended scaffold - (correct Answer) - Single point
A bosins chair is a ____ ____ scaffold - (correct Answer) - Light duty
The safety equipment required when using a hammer is - (correct Answer) - Safety glasses
14. A light duty scafiold is rated at _____ lb per square foot of decking. - (correct Answer) - 25 lb
A medium duty scaffold is rated at ___ pounds per square foot of decking. - (correct Answer) - 50 pounds
A heavy duty scaffoid is rated at ___ pounds per square foot of decking. - (correct Answer) - 75 pounds
Right angle clamps should be tightened at ___ lb torque. - (correct Answer) - 45 lb
When using a scaffold wrench you should always _____ _____ from your body. - (correct Answer) - Push
away
Snap hooks and d rings on safety harness are rated to hold ____. - (correct Answer) - 5000 lb
- (correct Answer) - Screw jacks (laying lacks)
- (correct Answer) - Torpedo level
- (correct Answer) - Scaffold post
