CE13B - Final Test (Life Critical Rules
1-4)Exam 2025 With 100% Correct
Answers
Which rules are applicable to LCR #1 (Getting on and Off Equipment)? - CORRECT ANSWER✔✔-
GOI Section 8 - 12.5: Entraining and Detraining
- CROR General Rule C (iii - Standing Clear of Approaching Equipment
Summarize GOI Section 8 - 12.5: Entraining and Detraining - CORRECT ANSWER✔✔- Do not
entrain or detrain while any equipment is in motion.
- Use three points of contact while entraining or detraining and face the equipment until both
feet are on the ground.
- Place carried objects on the equipment before boarding and remove articles after reaching the
ground when detraining after a stop has been made.
Summarize CROR General Rule C (iii - Standing Clear of Approaching Equipment) - CORRECT
ANSWER✔✔Do not stand in front of moving trains 😊
Which rules are applicable to LCR #2 (Going In Between Equipment)? - CORRECT ANSWER✔✔-
GOI Section 8 - 4.5.3: Working on or Near Tracks
- GOI Section 8 - 4.6.13: On or About Equipment: Set and Centered
- GOI Section 8 - 4.6.14: Anglecocks
,- GOI Section 8 - 4.6.15: OCU Snagging Hazard
- GOI Section 8 - 12.9: Crossing Between Coupled Equipment
Summarize GOI Section 8 - 4.5.3: Working on or Near Tracks - CORRECT ANSWER✔✔- Look in
both directions before crossing tracks.
- Walk no less than 25 feet from standing equipment not under your control.
Summarize GOI Section 8 - 4.6.13: On or About Equipment: Set and Centered - CORRECT
ANSWER✔✔- Always maintain 50 feet between equipment, unless aligning drawbars on a non-
tangent track which requires a distance of 6-12 feet in order to properly visualize the alignment
prior to coupling.
- When performing work in between cars - with the exception of applying handbrakes - set and
centered confirmation must be obtained from the Locomotive Engineer, and work must not
commence until the following conditions have been met:
1. The movement has come to a stop
2. All slack action has ceased
3. Confirm that there are no other movements on the same track on which you are working
4. The employee advises the Locomotive Engineer of the intended activity (e.g., "5634, I am
going in between to cut in the air.")
, 5. When so informed, the employee controlling the locomotive must:
a. Fully apply the independent brake
b. Center the reverser
c. Respond to the employee on the ground (e.g., "5634 set and centered.")
d. Brakes must remain applied and reverser centered until the employee performing the work
states that he/she is in the clear (e.g., "5634, I am in the clear.")
e. Locomotive Engineer confirms that employee is in the clear (e.g., "5634, you are in the
clear?")
What distance is required for re-aligning drawbars on a non-tangent (curved) track?
(GOI Section 8 - 4.6.13: On or About Equipment: Set and Centered) - CORRECT ANSWER✔✔1.
Separate 6-12 feet away to visually inspect the drawbars.
2. Separate even further to 50 feet in order to safely go in between equipment to manually re-
align the drawbars.
3. Close the gap to 6-12 feet to visually inspect the drawbar alignment one last time before
making the coupling.
What other time other than immediately after confirming the equipment has been set and
centered must an employee expect slack action?
(GOI Section 8 - 4.6.13: On or About Equipment: Set and Centered) - CORRECT
ANSWER✔✔When required to close an angle cock in order to restore air pressure (as in the
case of separated equipment), the employee must then ensure they remain clear of equipment
and expect slack action to occur at any time as the brakes release.
1-4)Exam 2025 With 100% Correct
Answers
Which rules are applicable to LCR #1 (Getting on and Off Equipment)? - CORRECT ANSWER✔✔-
GOI Section 8 - 12.5: Entraining and Detraining
- CROR General Rule C (iii - Standing Clear of Approaching Equipment
Summarize GOI Section 8 - 12.5: Entraining and Detraining - CORRECT ANSWER✔✔- Do not
entrain or detrain while any equipment is in motion.
- Use three points of contact while entraining or detraining and face the equipment until both
feet are on the ground.
- Place carried objects on the equipment before boarding and remove articles after reaching the
ground when detraining after a stop has been made.
Summarize CROR General Rule C (iii - Standing Clear of Approaching Equipment) - CORRECT
ANSWER✔✔Do not stand in front of moving trains 😊
Which rules are applicable to LCR #2 (Going In Between Equipment)? - CORRECT ANSWER✔✔-
GOI Section 8 - 4.5.3: Working on or Near Tracks
- GOI Section 8 - 4.6.13: On or About Equipment: Set and Centered
- GOI Section 8 - 4.6.14: Anglecocks
,- GOI Section 8 - 4.6.15: OCU Snagging Hazard
- GOI Section 8 - 12.9: Crossing Between Coupled Equipment
Summarize GOI Section 8 - 4.5.3: Working on or Near Tracks - CORRECT ANSWER✔✔- Look in
both directions before crossing tracks.
- Walk no less than 25 feet from standing equipment not under your control.
Summarize GOI Section 8 - 4.6.13: On or About Equipment: Set and Centered - CORRECT
ANSWER✔✔- Always maintain 50 feet between equipment, unless aligning drawbars on a non-
tangent track which requires a distance of 6-12 feet in order to properly visualize the alignment
prior to coupling.
- When performing work in between cars - with the exception of applying handbrakes - set and
centered confirmation must be obtained from the Locomotive Engineer, and work must not
commence until the following conditions have been met:
1. The movement has come to a stop
2. All slack action has ceased
3. Confirm that there are no other movements on the same track on which you are working
4. The employee advises the Locomotive Engineer of the intended activity (e.g., "5634, I am
going in between to cut in the air.")
, 5. When so informed, the employee controlling the locomotive must:
a. Fully apply the independent brake
b. Center the reverser
c. Respond to the employee on the ground (e.g., "5634 set and centered.")
d. Brakes must remain applied and reverser centered until the employee performing the work
states that he/she is in the clear (e.g., "5634, I am in the clear.")
e. Locomotive Engineer confirms that employee is in the clear (e.g., "5634, you are in the
clear?")
What distance is required for re-aligning drawbars on a non-tangent (curved) track?
(GOI Section 8 - 4.6.13: On or About Equipment: Set and Centered) - CORRECT ANSWER✔✔1.
Separate 6-12 feet away to visually inspect the drawbars.
2. Separate even further to 50 feet in order to safely go in between equipment to manually re-
align the drawbars.
3. Close the gap to 6-12 feet to visually inspect the drawbar alignment one last time before
making the coupling.
What other time other than immediately after confirming the equipment has been set and
centered must an employee expect slack action?
(GOI Section 8 - 4.6.13: On or About Equipment: Set and Centered) - CORRECT
ANSWER✔✔When required to close an angle cock in order to restore air pressure (as in the
case of separated equipment), the employee must then ensure they remain clear of equipment
and expect slack action to occur at any time as the brakes release.
