Testout Network Pro Exam| Complete Exam
Questions and CORRECT Answers| (2025-2026
update) Assured success| grade A+
You manage a single Spanning tree
subnet with three
switches. The switches are
connected to provide
redundant paths between
the switches.
Which feature prevents
switching loops and
ensures there is only a
single active patch
between any two
switches?
Which feature prevents spanning trees
switching loops and
ensures there is only a
single active path
between any two
switches?
,A user reports that Duplex mismatch
network access from her
workstation is very slow.
The problem does not
seem to be affecting any
other users.
Which of the following
conditions is the most
likely cause?
You manage a local Incorrect VLAN assignment
area network with
several switches. A
new employee has
started today so you
connect her
workstation to a switch
port.
Which of the following
is the most likely cause
of the problem?
,You manage a network Enable spanning tree on the switches
with multiple switches. You
find that your switches are
experiencing heavy
broadcast storms.
Which of the following will
help reduce the effects of
a broadcast storm?
Which of the following spanning tree
solutions would you
implement to eliminate
switching loops?
While viewing the status of The workstation's network board is jabbering
the interfaces on a Cisco
switch, you see
abnormally large of
oversized ethernet frames
being received on one
interface. This interface is
connected to a
workstation located on
the 2nd floor.
What could be causing
this to happen?
, The network board in a show running-config interface
workstation is currently show interface
configured as follows:
You manage a single Trunking
subnet with three
switches. The switches are
connected to provide
redundant paths between
the switches.
Which feature allows the
switches to pass VLAN
traffic between the
switches?
You manage a network Trunking
with two switches. The
switches are connected
together through their
Gigabit Ethernet uplink
ports.
You define VLAN 1 and
VLAN 2 on each switch. A
device on the first switch
in VLAN 1 needs to
communicate with a
device on the second
switch also in VLAN 1.
What should you
configure to allow
communication between
these two devices through
the switches?
Questions and CORRECT Answers| (2025-2026
update) Assured success| grade A+
You manage a single Spanning tree
subnet with three
switches. The switches are
connected to provide
redundant paths between
the switches.
Which feature prevents
switching loops and
ensures there is only a
single active patch
between any two
switches?
Which feature prevents spanning trees
switching loops and
ensures there is only a
single active path
between any two
switches?
,A user reports that Duplex mismatch
network access from her
workstation is very slow.
The problem does not
seem to be affecting any
other users.
Which of the following
conditions is the most
likely cause?
You manage a local Incorrect VLAN assignment
area network with
several switches. A
new employee has
started today so you
connect her
workstation to a switch
port.
Which of the following
is the most likely cause
of the problem?
,You manage a network Enable spanning tree on the switches
with multiple switches. You
find that your switches are
experiencing heavy
broadcast storms.
Which of the following will
help reduce the effects of
a broadcast storm?
Which of the following spanning tree
solutions would you
implement to eliminate
switching loops?
While viewing the status of The workstation's network board is jabbering
the interfaces on a Cisco
switch, you see
abnormally large of
oversized ethernet frames
being received on one
interface. This interface is
connected to a
workstation located on
the 2nd floor.
What could be causing
this to happen?
, The network board in a show running-config interface
workstation is currently show interface
configured as follows:
You manage a single Trunking
subnet with three
switches. The switches are
connected to provide
redundant paths between
the switches.
Which feature allows the
switches to pass VLAN
traffic between the
switches?
You manage a network Trunking
with two switches. The
switches are connected
together through their
Gigabit Ethernet uplink
ports.
You define VLAN 1 and
VLAN 2 on each switch. A
device on the first switch
in VLAN 1 needs to
communicate with a
device on the second
switch also in VLAN 1.
What should you
configure to allow
communication between
these two devices through
the switches?
