SACA EXAM QUESTIONS AND ANSWERS
What is the pressure shown on this gauge?* - -500 kPa
-What type of wrench is shown?* - -Ratchet
-What amount of power is used in this circuit?* - -96W
-What type of geometric tolerance is shown in the feature control frame on this drawing? -
-Circularity
-A company's Emergency Action Plan (EAP) should include ALL of the following except? - -
Machine operation procedures
-What action must be taken to correctly position a dial caliper? - -Sweep and rock to the
jaws
-What type of hand tool has a cross-shaped head to engage and tighten a fastener?* - -
Phillips head screwdriver
-Which of these activities is considered non-value added activity in a lean manufacturing
environment?*
0/4 - -Moving a product from one station to another
-What is the tolerance of the width of this part?* - -+/-0.1
-What do SDS sheets do?* - -Specify material hazards.
-When a click-type torque wrench clicks at the set point, what do you do to apply the
proper torque? - -Stop turning the wrench
-What type of hole is identified by the arrow labeled A?* - -Blind
-What component does the schematic represent?* - -Pneumatic motor
-What type of information would not normally be found in a drawing's title block?*
0/4 - -General notes
-What machine can be programmed to perform tasks in many different operations? - -
Robot
-What could affect an inductive sensor's operation if it is mounted near the sensor?*
4/4 - -metal
, -Which of these is NOT a primary goal of a lean manufacturing system? - -Greater
production volume
-In the bolt designation shown, what is the pitch? - -2.5
-What air pressure should be used when compressed air is used to clean or blow parts? - -
Below 30 psi
-If a machine stops unexpectedly due to a fault, which message tells you only that the
machine has a fault? - -Warning message
-What material condition does LMC define?* - -Condition with the smallest amount of
material
-What method do most small air compressors use to compress air - -Piston movement
-If an electronic sensor has a PNP type transistor, what effect does that have on the
sensor's operations? - -Output signal goes high when the sensor is triggered.
-What is used to calibrate a precision measuring instrument?* - -Gauge block
-What is the scale of the drawing if the actual length of this part is 300 mm and dimension
shown by X measures 50 mm on the drawing? - -1:6
-What is the measurement shown on this SI dial caliper, in millimeters? - -22.68 mm
-What is NOT a step in an electrical Lockout/Tagout procedure?* - -Write safety officer
initials on tag
-What type of technical drawing shows the features of a 3-dimensional object in 2
dimensions as seen from different sides of the object? - -Multiview drawing
-What is the measurement shown on this micrometer in millimeters? - -39.21
-What type of logic does this schematic represent? - -AND
-Which of these components is used to keep the motor turned on after the start
pushbutton is momentarily activated? - -CR1A
-In addition to a material block, what is another way a technical drawing can identify the
type of material used to make the drawn object? - -Local note
-What is the hazardous material classification system that uses pictograms to identify the
danger of a material? - -GHS
What is the pressure shown on this gauge?* - -500 kPa
-What type of wrench is shown?* - -Ratchet
-What amount of power is used in this circuit?* - -96W
-What type of geometric tolerance is shown in the feature control frame on this drawing? -
-Circularity
-A company's Emergency Action Plan (EAP) should include ALL of the following except? - -
Machine operation procedures
-What action must be taken to correctly position a dial caliper? - -Sweep and rock to the
jaws
-What type of hand tool has a cross-shaped head to engage and tighten a fastener?* - -
Phillips head screwdriver
-Which of these activities is considered non-value added activity in a lean manufacturing
environment?*
0/4 - -Moving a product from one station to another
-What is the tolerance of the width of this part?* - -+/-0.1
-What do SDS sheets do?* - -Specify material hazards.
-When a click-type torque wrench clicks at the set point, what do you do to apply the
proper torque? - -Stop turning the wrench
-What type of hole is identified by the arrow labeled A?* - -Blind
-What component does the schematic represent?* - -Pneumatic motor
-What type of information would not normally be found in a drawing's title block?*
0/4 - -General notes
-What machine can be programmed to perform tasks in many different operations? - -
Robot
-What could affect an inductive sensor's operation if it is mounted near the sensor?*
4/4 - -metal
, -Which of these is NOT a primary goal of a lean manufacturing system? - -Greater
production volume
-In the bolt designation shown, what is the pitch? - -2.5
-What air pressure should be used when compressed air is used to clean or blow parts? - -
Below 30 psi
-If a machine stops unexpectedly due to a fault, which message tells you only that the
machine has a fault? - -Warning message
-What material condition does LMC define?* - -Condition with the smallest amount of
material
-What method do most small air compressors use to compress air - -Piston movement
-If an electronic sensor has a PNP type transistor, what effect does that have on the
sensor's operations? - -Output signal goes high when the sensor is triggered.
-What is used to calibrate a precision measuring instrument?* - -Gauge block
-What is the scale of the drawing if the actual length of this part is 300 mm and dimension
shown by X measures 50 mm on the drawing? - -1:6
-What is the measurement shown on this SI dial caliper, in millimeters? - -22.68 mm
-What is NOT a step in an electrical Lockout/Tagout procedure?* - -Write safety officer
initials on tag
-What type of technical drawing shows the features of a 3-dimensional object in 2
dimensions as seen from different sides of the object? - -Multiview drawing
-What is the measurement shown on this micrometer in millimeters? - -39.21
-What type of logic does this schematic represent? - -AND
-Which of these components is used to keep the motor turned on after the start
pushbutton is momentarily activated? - -CR1A
-In addition to a material block, what is another way a technical drawing can identify the
type of material used to make the drawn object? - -Local note
-What is the hazardous material classification system that uses pictograms to identify the
danger of a material? - -GHS
