ICC Philadelphia PA 211 Master Electrician Exam Actual Exam Preparation
ICC PHILADELPHIA PA 211 MASTER ELECTRICIAN EXAM ACTUAL
EXAM PREPARATION NEWEST 2025/2026 COMPLETE
QUESTIONS AND CORRECT DETAILED ANSWERS (VERIFIED
ANSWERS) |BRAND NEW VERSION!!
A group of devices that serve to govern in some predetermined manner the
electric power delivered to the apparatus to which it is connected is a ?
A) Device
B) Controller
C) Disconnect
D) Circuit breaker
Controller
(article 100)
For a service panel fed by parallel 3/0 AWG copper conductors, the copper
GROUNDING - ELECTRODE run from the service panel to the metallic water service
shall be at least size ____________ AWG
A) 4
B) 2
C) 1/0
D) 2/0
2
(table 250.66)
A dry - type TRANSFORMER may be LOCATED in a suspended ceiling space where
it is not ready ACCESSIBLE if the voltage is 600 volts or less and has a maximum
rating of ____________ kva
1|Page
, ICC Philadelphia PA 211 Master Electrician Exam Actual Exam Preparation
A) 10
B) 25
C) 50
D( 112
50
(article 450.13 (B) )
A SERVICE head can be located no further away from the point of attachment than
____________ inches
A) 18
B) 24
C) 36
D) 48
24"
(article 230.54) (C) (exceptions)
ACCEPTABLE METHODS of connecting GROUNDING and BONDING conductors
include all the following, EXCEPT:
A) Solder joints
B) Terminal bars
C) Exothermic weld
D) Listed pressure connectors
solder joints
(article 250.8 (A)
The amount of available fault current at the service depends upon the :
2|Page
, ICC Philadelphia PA 211 Master Electrician Exam Actual Exam Preparation
A) Method of bonding
B) Method of grounding
C) Size and impedance of the service transformer
D) Ampere rating of the over current protection device
Size and impedance of the service transformer
( general knowledge )
For a residential service calculation, heat pump loads are required to be calculated
at _______________ percent of the nameplate rating when used without any
supplemental electric heating.
A) 65
B) 80
C) 100
D) 125
100%
(article 220.82 (C) (2) )
Where the footing steel serves as the only grounding electrode for a building ,
does the code require a maximum resistance in ohms for this concrete encased
electrode?
A) Yes, 0 ohms
B) Yes, 25 ohms
C) Yes, 50 ohms
D) No, the code has no resistance requirements for footing steel electrodes
3|Page
ICC PHILADELPHIA PA 211 MASTER ELECTRICIAN EXAM ACTUAL
EXAM PREPARATION NEWEST 2025/2026 COMPLETE
QUESTIONS AND CORRECT DETAILED ANSWERS (VERIFIED
ANSWERS) |BRAND NEW VERSION!!
A group of devices that serve to govern in some predetermined manner the
electric power delivered to the apparatus to which it is connected is a ?
A) Device
B) Controller
C) Disconnect
D) Circuit breaker
Controller
(article 100)
For a service panel fed by parallel 3/0 AWG copper conductors, the copper
GROUNDING - ELECTRODE run from the service panel to the metallic water service
shall be at least size ____________ AWG
A) 4
B) 2
C) 1/0
D) 2/0
2
(table 250.66)
A dry - type TRANSFORMER may be LOCATED in a suspended ceiling space where
it is not ready ACCESSIBLE if the voltage is 600 volts or less and has a maximum
rating of ____________ kva
1|Page
, ICC Philadelphia PA 211 Master Electrician Exam Actual Exam Preparation
A) 10
B) 25
C) 50
D( 112
50
(article 450.13 (B) )
A SERVICE head can be located no further away from the point of attachment than
____________ inches
A) 18
B) 24
C) 36
D) 48
24"
(article 230.54) (C) (exceptions)
ACCEPTABLE METHODS of connecting GROUNDING and BONDING conductors
include all the following, EXCEPT:
A) Solder joints
B) Terminal bars
C) Exothermic weld
D) Listed pressure connectors
solder joints
(article 250.8 (A)
The amount of available fault current at the service depends upon the :
2|Page
, ICC Philadelphia PA 211 Master Electrician Exam Actual Exam Preparation
A) Method of bonding
B) Method of grounding
C) Size and impedance of the service transformer
D) Ampere rating of the over current protection device
Size and impedance of the service transformer
( general knowledge )
For a residential service calculation, heat pump loads are required to be calculated
at _______________ percent of the nameplate rating when used without any
supplemental electric heating.
A) 65
B) 80
C) 100
D) 125
100%
(article 220.82 (C) (2) )
Where the footing steel serves as the only grounding electrode for a building ,
does the code require a maximum resistance in ohms for this concrete encased
electrode?
A) Yes, 0 ohms
B) Yes, 25 ohms
C) Yes, 50 ohms
D) No, the code has no resistance requirements for footing steel electrodes
3|Page
