SACA C-202 Electric Motor Control Systems
ACTUAL EXAM 2025/2026 QUESTIONS WITH
VERIFIED CORRECT SOLUTIONS || 100%
GUARANTEED PASS <BRAND NEW VERSION>
Fuse - ANSWER Which of the following is a type of circuit protection device?
Full Load Amperage - ANSWER Which term is defined by the total operating
current of a circuit?
Relays - ANSWER Devices called __________ often serve as the brains of an
automated machine.
Output - ANSWER What devices are wired to the relay circuit and are turned on
in sequence to create the steps of operation?
NOR - ANSWER Which of the following elements describes two or more
normally closed input switches in series?
NOR
NOT
NAND
OR
Memory - ANSWER A motor control circuit is a common application of what
type of logic element?
AND - ANSWER Which one of the following logic elements describes a circuit
with two normally open input switches in series?
,OR
NAND
AND
NOT
Electrical schematic - ANSWER What type of drawing is a ladder diagram?
Valve - ANSWER Which of the following is not a component of a ladder
diagram?
Input device
Output device
Conductor
Valve
Motor starter - ANSWER What device is used before a motor that allows
electricity to flow to the motor?
Determine the power device operation when the output is energized - ANSWER A
power diagram is needed with a ladder diagram to __________.
NO contacts, NC contacts, and a solenoid coil - ANSWER An electromechanical
relay includes which of these components?
Two sets of NO contacts, and a solenoid coil
NO contacts, NC contacts, and a solenoid coil
Two sets of NC contacts, and a solenoid coil
NO and NC contacts and a ferrous element
Output - ANSWER Which type of device is the relay's solenoid coil in the control
logic?
Control logic - ANSWER Turning outputs on or off through relay contacts is
called __________.
Stationary or mobile - ANSWER Robots are classified into four groups: type of
motion, servo or non-servo, number of axes, and __________.
, Delta - ANSWER These robots are used in the food, pharmaceutical, and
electronics industries.
Teach pendant - ANSWER Servo Robots use Pmove or point move to program the
robots movements. The points are most often recorded using a __________.
Sequencing the steps - ANSWER What is the purpose of the robot program?
Emergency stop - ANSWER Many of the safety devices for the robot are designed
to protect the human interaction with the robot. Which is the only safety device
designed for the operator to protect the robot?
Checking dress code, clean and clear workcell - ANSWER Powering up a servo
robot includes more than just turning on the power. A safety precheck is completed
before any power up. The precheck includes __________.
Function - ANSWER The three Fs of product design are form, fit and __________.
Lean Manufacturing - ANSWER High product quality, quick delivery, low costs
are the primary goals of what system?
Standardize - ANSWER Which 5S step involves formatting 5S work instructions
so that they look and read alike?
Reduces the waste of excess motion, helps improve morale, and enables other lean
methods to be more successful - ANSWER How does the 5S method aid in the
goal of lean manufacturing?
HMI - ANSWER What is the interface used with CNC machines to load and
monitor programs?
PLC - ANSWER The automation of many different manufacturing processes is
done through the use of a small computer called a __________.
ACTUAL EXAM 2025/2026 QUESTIONS WITH
VERIFIED CORRECT SOLUTIONS || 100%
GUARANTEED PASS <BRAND NEW VERSION>
Fuse - ANSWER Which of the following is a type of circuit protection device?
Full Load Amperage - ANSWER Which term is defined by the total operating
current of a circuit?
Relays - ANSWER Devices called __________ often serve as the brains of an
automated machine.
Output - ANSWER What devices are wired to the relay circuit and are turned on
in sequence to create the steps of operation?
NOR - ANSWER Which of the following elements describes two or more
normally closed input switches in series?
NOR
NOT
NAND
OR
Memory - ANSWER A motor control circuit is a common application of what
type of logic element?
AND - ANSWER Which one of the following logic elements describes a circuit
with two normally open input switches in series?
,OR
NAND
AND
NOT
Electrical schematic - ANSWER What type of drawing is a ladder diagram?
Valve - ANSWER Which of the following is not a component of a ladder
diagram?
Input device
Output device
Conductor
Valve
Motor starter - ANSWER What device is used before a motor that allows
electricity to flow to the motor?
Determine the power device operation when the output is energized - ANSWER A
power diagram is needed with a ladder diagram to __________.
NO contacts, NC contacts, and a solenoid coil - ANSWER An electromechanical
relay includes which of these components?
Two sets of NO contacts, and a solenoid coil
NO contacts, NC contacts, and a solenoid coil
Two sets of NC contacts, and a solenoid coil
NO and NC contacts and a ferrous element
Output - ANSWER Which type of device is the relay's solenoid coil in the control
logic?
Control logic - ANSWER Turning outputs on or off through relay contacts is
called __________.
Stationary or mobile - ANSWER Robots are classified into four groups: type of
motion, servo or non-servo, number of axes, and __________.
, Delta - ANSWER These robots are used in the food, pharmaceutical, and
electronics industries.
Teach pendant - ANSWER Servo Robots use Pmove or point move to program the
robots movements. The points are most often recorded using a __________.
Sequencing the steps - ANSWER What is the purpose of the robot program?
Emergency stop - ANSWER Many of the safety devices for the robot are designed
to protect the human interaction with the robot. Which is the only safety device
designed for the operator to protect the robot?
Checking dress code, clean and clear workcell - ANSWER Powering up a servo
robot includes more than just turning on the power. A safety precheck is completed
before any power up. The precheck includes __________.
Function - ANSWER The three Fs of product design are form, fit and __________.
Lean Manufacturing - ANSWER High product quality, quick delivery, low costs
are the primary goals of what system?
Standardize - ANSWER Which 5S step involves formatting 5S work instructions
so that they look and read alike?
Reduces the waste of excess motion, helps improve morale, and enables other lean
methods to be more successful - ANSWER How does the 5S method aid in the
goal of lean manufacturing?
HMI - ANSWER What is the interface used with CNC machines to load and
monitor programs?
PLC - ANSWER The automation of many different manufacturing processes is
done through the use of a small computer called a __________.
