Solutions Manual – Solid State Electronic Devices
An AND gate is a logic gate that provides logic level 1 only if all inputs are at logic level ____. -
ANSWERS1
A(n) ____ input is a digital input that is not a true high or low at all times. - ANSWERSfloating
Two major logic family groups are the transistor-transistor and ____ families. -
ANSWERScomplementary metal-oxide semiconductor
____ signals are continually changing signals. - ANSWERSAnalog
Today, it is more common to measure pulse ____ between the 50% points of the pulse. -
ANSWERSwidth duration
A clock is simply a device that outputs highs and lows, one after another, in a carefully timed
sequence called a(n) ____. - ANSWERSpulse
A(n) ____ gate is a logic gate that provides an output that is opposite of the input. -
ANSWERSNOT
A(n) ____ IC is an integrated circuits that processes finite (zero and maximum) signal levels. -
ANSWERSdigital
Fault ____ is used to determine the cause and location of a fault. - ANSWERSisolation
A(n) ____ is a binary digit of either 0 or 1. - ANSWERSbit
, The transistor-transistor logic family is commonly referred to as the ____ series. -
ANSWERS7,400
A pull-up resistor is a resistor that has one side connected to a(n) ____ at all times and the other
side connected to unused gates._ - ANSWERSpower supply
____ are used to show the output of each logic function. - ANSWERSTruth tables
____ ICs are used to provide amplification and regulation functions. - ANSWERSLinear
____ logic is a family of digital circuits built from bipolar junction transistors and resistors. -
ANSWERSTranistor-transistor
____ gates are used in applications that require an output to turn off if any one of the input
conditions is above a set limit. - ANSWERSNOR
A(n) ____ is either high (1) or low (0). - ANSWERSbinary
ICs are powered and interconnected with other components through ____. - ANSWERSpins
____ is the number of loads that can be driven by the output of a logic gate. - ANSWERSFan-out
A(n) ____ is an electronic device in which all components (transistors, diodes, and resistors) are
contained in a single package or chip. - ANSWERSintegrated circuit IC
____ gates are used in applications that require an output to turn off only if all the inputs are at
logic level 1. - ANSWERSNAND
An AND gate is a logic gate that provides logic level 1 only if all inputs are at logic level ____. -
ANSWERS1
A(n) ____ input is a digital input that is not a true high or low at all times. - ANSWERSfloating
Two major logic family groups are the transistor-transistor and ____ families. -
ANSWERScomplementary metal-oxide semiconductor
____ signals are continually changing signals. - ANSWERSAnalog
Today, it is more common to measure pulse ____ between the 50% points of the pulse. -
ANSWERSwidth duration
A clock is simply a device that outputs highs and lows, one after another, in a carefully timed
sequence called a(n) ____. - ANSWERSpulse
A(n) ____ gate is a logic gate that provides an output that is opposite of the input. -
ANSWERSNOT
A(n) ____ IC is an integrated circuits that processes finite (zero and maximum) signal levels. -
ANSWERSdigital
Fault ____ is used to determine the cause and location of a fault. - ANSWERSisolation
A(n) ____ is a binary digit of either 0 or 1. - ANSWERSbit
, The transistor-transistor logic family is commonly referred to as the ____ series. -
ANSWERS7,400
A pull-up resistor is a resistor that has one side connected to a(n) ____ at all times and the other
side connected to unused gates._ - ANSWERSpower supply
____ are used to show the output of each logic function. - ANSWERSTruth tables
____ ICs are used to provide amplification and regulation functions. - ANSWERSLinear
____ logic is a family of digital circuits built from bipolar junction transistors and resistors. -
ANSWERSTranistor-transistor
____ gates are used in applications that require an output to turn off if any one of the input
conditions is above a set limit. - ANSWERSNOR
A(n) ____ is either high (1) or low (0). - ANSWERSbinary
ICs are powered and interconnected with other components through ____. - ANSWERSpins
____ is the number of loads that can be driven by the output of a logic gate. - ANSWERSFan-out
A(n) ____ is an electronic device in which all components (transistors, diodes, and resistors) are
contained in a single package or chip. - ANSWERSintegrated circuit IC
____ gates are used in applications that require an output to turn off only if all the inputs are at
logic level 1. - ANSWERSNAND
