MSSC Quality Exam Questions & Answers | 100% Verified solutions |Qu
tions with Correct Answers 2025 latest update!!
1. The dimensions of raw material supplied by metal stock size
suppliers are described by the __________.
2. Engineers sometimes use a ____________ to measure Protractor
angles on a drawing.
3. The three standard views of an object are____________. top, front, right side
4. What type of drawing is shown? "All three views of an Multiview
object."
5. Which drafting style requires a computer? CAD
6. An isometric drawing is a type of _________? pictorial drawing
7. What dimension is indicated in the graphic? "Front Height
view from bottom to top?"
8. In manufacturing, a blueprint is also called what? a technical drawing
9. Which of the following steps is not used in the glass Rotate object in a glass
box method? box
10. The number of views in a drawing __________. is the fewest number that
shows all the features and
dimensions
11. what is the order of precedence of lines in a drawing? object, hidden, center
12. The holes to be drilled in the part are represented by Hidden lines
_________. "Shows dashed lines through part"
13. Object line
, MSSC Quality Exam Questions & Answers | 100% Verified solutions |Qu
tions with Correct Answers 2025 latest update!!
What type best describes the line in the graphic? "re-
versed capital L pointing at the outside upright leg
line."
14. Dimensions are used to specify the _________ and loca- size
tion of the features of an object.
15. a _________ dimension is described in inches per foot. shaft taper
16. there are 60 minutes of arc in one _________. degree
17. in the graphic shown, the two circles are _________. concentric
"there are two circles, one inside the other the same
plane and same distance apart around the circumfer-
ence"
18. what features in the figure shown is a chamfer? D.
A- is a flat plane
b- seems to be an alignment pin
c- is a hidden hole
d-is the cut off edge of a 90 degree
19. which type of feature is parallel to the surface being Dimension Line
dimensioned?
20. the length of the part shown in the drawing is _________ 9-3/4
inches. "Lots of lines but look for the overall lines"
21. which of the following is NOT one of the six rules for c-dimension hidden lines
dimensioning and object?
a-do not over dimension
b-Dimension in the view that most clearly shows the
feature
, MSSC Quality Exam Questions & Answers | 100% Verified solutions |Qu
tions with Correct Answers 2025 latest update!!
c-dimension hidden lines
d-dimension an object completely
22. The distance across the flats of the hex head shown 2-1/4
in the part drawing is __________ inches. "find the hex
head and go from flat to flat.
23. the hole shown in the graphic is a(n) __________ hole. counterbore
"shows a hole with a noticeable shoulder passing com-
pletely through part"
24. What type hole is shown in the figure? "dashes lines counterbored
show hole with a squared edge as it steps down a size"
25. where would you look in a title block to see if there has revision number
been changes?
26. the material that will be used to create the gear is indi- cast iron
cated in the part drawings title block to be __________?
"Look at the MATL: section"
27. to establish on a drawing that 1/4 inch equals 1 inch, 1/4=1
the designer would write ___________.
28. the feature on a drawing is drawn 3 inches long and 12"
the scale is 1:4, what is the actual dimension on the
object?
29. What is the depth of the countersink in the image? 0.12 inches
"look at the countersunk hole and only pay attention
to the countersunk portion"
30. drawing revision level
tions with Correct Answers 2025 latest update!!
1. The dimensions of raw material supplied by metal stock size
suppliers are described by the __________.
2. Engineers sometimes use a ____________ to measure Protractor
angles on a drawing.
3. The three standard views of an object are____________. top, front, right side
4. What type of drawing is shown? "All three views of an Multiview
object."
5. Which drafting style requires a computer? CAD
6. An isometric drawing is a type of _________? pictorial drawing
7. What dimension is indicated in the graphic? "Front Height
view from bottom to top?"
8. In manufacturing, a blueprint is also called what? a technical drawing
9. Which of the following steps is not used in the glass Rotate object in a glass
box method? box
10. The number of views in a drawing __________. is the fewest number that
shows all the features and
dimensions
11. what is the order of precedence of lines in a drawing? object, hidden, center
12. The holes to be drilled in the part are represented by Hidden lines
_________. "Shows dashed lines through part"
13. Object line
, MSSC Quality Exam Questions & Answers | 100% Verified solutions |Qu
tions with Correct Answers 2025 latest update!!
What type best describes the line in the graphic? "re-
versed capital L pointing at the outside upright leg
line."
14. Dimensions are used to specify the _________ and loca- size
tion of the features of an object.
15. a _________ dimension is described in inches per foot. shaft taper
16. there are 60 minutes of arc in one _________. degree
17. in the graphic shown, the two circles are _________. concentric
"there are two circles, one inside the other the same
plane and same distance apart around the circumfer-
ence"
18. what features in the figure shown is a chamfer? D.
A- is a flat plane
b- seems to be an alignment pin
c- is a hidden hole
d-is the cut off edge of a 90 degree
19. which type of feature is parallel to the surface being Dimension Line
dimensioned?
20. the length of the part shown in the drawing is _________ 9-3/4
inches. "Lots of lines but look for the overall lines"
21. which of the following is NOT one of the six rules for c-dimension hidden lines
dimensioning and object?
a-do not over dimension
b-Dimension in the view that most clearly shows the
feature
, MSSC Quality Exam Questions & Answers | 100% Verified solutions |Qu
tions with Correct Answers 2025 latest update!!
c-dimension hidden lines
d-dimension an object completely
22. The distance across the flats of the hex head shown 2-1/4
in the part drawing is __________ inches. "find the hex
head and go from flat to flat.
23. the hole shown in the graphic is a(n) __________ hole. counterbore
"shows a hole with a noticeable shoulder passing com-
pletely through part"
24. What type hole is shown in the figure? "dashes lines counterbored
show hole with a squared edge as it steps down a size"
25. where would you look in a title block to see if there has revision number
been changes?
26. the material that will be used to create the gear is indi- cast iron
cated in the part drawings title block to be __________?
"Look at the MATL: section"
27. to establish on a drawing that 1/4 inch equals 1 inch, 1/4=1
the designer would write ___________.
28. the feature on a drawing is drawn 3 inches long and 12"
the scale is 1:4, what is the actual dimension on the
object?
29. What is the depth of the countersink in the image? 0.12 inches
"look at the countersunk hole and only pay attention
to the countersunk portion"
30. drawing revision level
