OECP EXAM QUESTIONS WITH COMPLETE SOLUTIONS
what type of fire extinguisher is required on a crane - -10BC
-what should am operator do in the event of a power line contact - -remain in the machine
unless fire or emergency
-what is the minimum distance from a 200kv power line - -20ft
-where must electrocution warnings be displayed - -1 in the cab, 2 on the outside
-a boom angle indicator does not show what? - -boom deflection
-hand signals must use what method? - -standard method
-An operator must obey a stop signal from who? - -anyone
-when using radio, telephone or electronic signals, receiving must be what? - -hands free
-what must voice signals include? - -function and direction, distance and speed, function
and stop
-what is the minimum number of wraps on a drum - -2
-most LMI's will not indicate - -Levelness
-if signals are interrupted the operator must do what? - -stop safety
-all directions must be given in the operator's what? - -perspective
-what are the ANSI/ASME audible signals - -1 stop
2 forward
3 reverse
-when can an LMI be used to weigh a load? - -up to 75% of capacity at the working radius
-what is the correct procedure if an LMI fails? - -use the load chart and the boom angle
unless not allowed by the manufacturer
-what functions are disabled by a kick-out system? - -hoist up, boom down, telescope out
-power lines are always presumed what? - -energized
-travel distance on 2 way levers shall not exceed what? - -14 inches from neutral
, -forces shall not be greater than what on a foot pedal? - -50 pounds
-a crane traveling at 15 mph must be able to stop in what distance? - -32 feet
-what does PCSA stand for? - -power crane and shovel association
-what is the safety factor for synthetic slings? - -5 to 1
-what is PS - -plow steel
-an annual inspection must be performed by a - -qualified person
-what is the construction rigging standard? - -1926.251
-what is the general industry rigging standard - -1910.184
-what is the general industry crane standard - -1910.180
-what is the construction crane standard - -1926.1400 also known as subpart cc
-what is the ANSI/ASME standard for construction crane - -B30.5
-what does ANSI stand for - -American national standards institute
-what does ASME stand for? - -American society of mechanical engineers
-what does CFR stand for - -code of federal regulations
-what part of the load charts does not show boom deflection - -range diagram
-A deduction should be made for an extension even when lifting from it?
true or false - -false
-what do asterisks signify on a load chart - -structural capacity
-the maximum list allowed for a land crane on a barge is? - -5 degrees
-land cranes on a barge fall under what ANSI standard - -B30.8
-dynamic movement of a barge can make lifts be what? - -Unpredictable
-Never ballast an open hull barge with what? - -water
-what is the distance between the waterline and the deck of a barge? - -Freeboard
-the movement of a barge from side to side is called? - -list
what type of fire extinguisher is required on a crane - -10BC
-what should am operator do in the event of a power line contact - -remain in the machine
unless fire or emergency
-what is the minimum distance from a 200kv power line - -20ft
-where must electrocution warnings be displayed - -1 in the cab, 2 on the outside
-a boom angle indicator does not show what? - -boom deflection
-hand signals must use what method? - -standard method
-An operator must obey a stop signal from who? - -anyone
-when using radio, telephone or electronic signals, receiving must be what? - -hands free
-what must voice signals include? - -function and direction, distance and speed, function
and stop
-what is the minimum number of wraps on a drum - -2
-most LMI's will not indicate - -Levelness
-if signals are interrupted the operator must do what? - -stop safety
-all directions must be given in the operator's what? - -perspective
-what are the ANSI/ASME audible signals - -1 stop
2 forward
3 reverse
-when can an LMI be used to weigh a load? - -up to 75% of capacity at the working radius
-what is the correct procedure if an LMI fails? - -use the load chart and the boom angle
unless not allowed by the manufacturer
-what functions are disabled by a kick-out system? - -hoist up, boom down, telescope out
-power lines are always presumed what? - -energized
-travel distance on 2 way levers shall not exceed what? - -14 inches from neutral
, -forces shall not be greater than what on a foot pedal? - -50 pounds
-a crane traveling at 15 mph must be able to stop in what distance? - -32 feet
-what does PCSA stand for? - -power crane and shovel association
-what is the safety factor for synthetic slings? - -5 to 1
-what is PS - -plow steel
-an annual inspection must be performed by a - -qualified person
-what is the construction rigging standard? - -1926.251
-what is the general industry rigging standard - -1910.184
-what is the general industry crane standard - -1910.180
-what is the construction crane standard - -1926.1400 also known as subpart cc
-what is the ANSI/ASME standard for construction crane - -B30.5
-what does ANSI stand for - -American national standards institute
-what does ASME stand for? - -American society of mechanical engineers
-what does CFR stand for - -code of federal regulations
-what part of the load charts does not show boom deflection - -range diagram
-A deduction should be made for an extension even when lifting from it?
true or false - -false
-what do asterisks signify on a load chart - -structural capacity
-the maximum list allowed for a land crane on a barge is? - -5 degrees
-land cranes on a barge fall under what ANSI standard - -B30.8
-dynamic movement of a barge can make lifts be what? - -Unpredictable
-Never ballast an open hull barge with what? - -water
-what is the distance between the waterline and the deck of a barge? - -Freeboard
-the movement of a barge from side to side is called? - -list
