1
For Expert help and assignment solutions, +254707240657
Facility Maintenance Technician Exam
Questions and Answers (100% Correct
Answers) Already Graded A+
Once a repair is completed, technicians must ___. [ANS:] Carefully
record the problem, causes, and solutions
___ maintenance is scheduled work required to keep equipment
in peak operating condition. [ANS:] Preventive
© 2025 Assignment Expert
___ maintenance is performed to minimize emergency work and
ensure reliable and efficient operations. [ANS:] Scheduled
Guru01 - Stuvia
A ___ is a document that details specific maintenance tasks to be
completed. [ANS:] Work order
The ___ is a federal government regulatory agency that requires
all employers to provide a safe working environment for their
employees. [ANS:] Occupational Safety and Health Administration
(OSHA)
Fall protection equipment is required when working in elevated
spaces (over ___' above the ground) or confined spaces. [ANS:] 6
A ___ does not prevent the start up of equipment, but it serves as
a warning to operating and service personnel. [ANS:] Tagout
NFPA 704, Standard system for the identification of the hazards of
materials for emergency response, uses a ___ -color diamond
design to display basic information about hazardous materials.
[ANS:] Four
, 2
For Expert help and assignment solutions, +254707240657
___ diagrams resemble a ladder, so they are also known as ladder
diagrams. [ANS:] Line
Updates to an operator's manual may be distributed as ___. [ANS:]
Service bulletins
Force can be measured in ___. [ANS:] Pounds
On the Celsius scale, ___ C is the freezing point. [ANS:] 0
___ keys are used for transmitting heavy torques in shafts and hubs
© 2025 Assignment Expert
that are reversed frequently and subject to vibration. [ANS:] Taper
___ are used to seal close-fitting pieces of metal such as parts of
an engine or pipe flanges. [ANS:] Gaskets
Guru01 - Stuvia
A belt drive is a ___ mechanical drive system that uses a belt and
pulleys to transfer power between two shafts. [ANS:]
Nonsynchronous
A(n) ___ bearing is a bearing that contains moving elements that
provide a low-friction support surface for rotating or sliding
surfaces. [ANS:] Antifriction
The lower portion of a gearbox is usually a ___. [ANS:] Reservoir for
lubricating internal gears
Poor bearing ___ allow dirt and other contaminants to enter the
bearing components. [ANS:] Seals
The power formula is the relationship between ___ in a circuit.
[ANS:] Power, voltage, and current
A ___ is a device that uses electricity, such as a lamp, heating
element, or motor, to produce a useful output. [ANS:] Load
For Expert help and assignment solutions, +254707240657
Facility Maintenance Technician Exam
Questions and Answers (100% Correct
Answers) Already Graded A+
Once a repair is completed, technicians must ___. [ANS:] Carefully
record the problem, causes, and solutions
___ maintenance is scheduled work required to keep equipment
in peak operating condition. [ANS:] Preventive
© 2025 Assignment Expert
___ maintenance is performed to minimize emergency work and
ensure reliable and efficient operations. [ANS:] Scheduled
Guru01 - Stuvia
A ___ is a document that details specific maintenance tasks to be
completed. [ANS:] Work order
The ___ is a federal government regulatory agency that requires
all employers to provide a safe working environment for their
employees. [ANS:] Occupational Safety and Health Administration
(OSHA)
Fall protection equipment is required when working in elevated
spaces (over ___' above the ground) or confined spaces. [ANS:] 6
A ___ does not prevent the start up of equipment, but it serves as
a warning to operating and service personnel. [ANS:] Tagout
NFPA 704, Standard system for the identification of the hazards of
materials for emergency response, uses a ___ -color diamond
design to display basic information about hazardous materials.
[ANS:] Four
, 2
For Expert help and assignment solutions, +254707240657
___ diagrams resemble a ladder, so they are also known as ladder
diagrams. [ANS:] Line
Updates to an operator's manual may be distributed as ___. [ANS:]
Service bulletins
Force can be measured in ___. [ANS:] Pounds
On the Celsius scale, ___ C is the freezing point. [ANS:] 0
___ keys are used for transmitting heavy torques in shafts and hubs
© 2025 Assignment Expert
that are reversed frequently and subject to vibration. [ANS:] Taper
___ are used to seal close-fitting pieces of metal such as parts of
an engine or pipe flanges. [ANS:] Gaskets
Guru01 - Stuvia
A belt drive is a ___ mechanical drive system that uses a belt and
pulleys to transfer power between two shafts. [ANS:]
Nonsynchronous
A(n) ___ bearing is a bearing that contains moving elements that
provide a low-friction support surface for rotating or sliding
surfaces. [ANS:] Antifriction
The lower portion of a gearbox is usually a ___. [ANS:] Reservoir for
lubricating internal gears
Poor bearing ___ allow dirt and other contaminants to enter the
bearing components. [ANS:] Seals
The power formula is the relationship between ___ in a circuit.
[ANS:] Power, voltage, and current
A ___ is a device that uses electricity, such as a lamp, heating
element, or motor, to produce a useful output. [ANS:] Load
