ESTIMATING TESTED EXAM QUESTIONS
WITH VERIFIED ANSWERS LATEST
UPDATE
Technician A says that a highly formed piece of sheet metal can be bent further than a
flat piece of sheet metal. Technician B says that the shape of the part may affect
whether kink vs. bend can be applied. - Answer- B only
Which of the following is true about rear lamp inspection? - Answer- To perform a
complete analysis, it may be necessary to partially disassemble the lamp assembly
Technician A says that contaminated fuel tanks should be replaced. Technician B says
that an incorrect fuel level reading could be due to the fuel pump and sending unit
shifting during a collision. B o - Answer- B only
Technician A says that exhaust soot on underbody parts may indicate a leak.
Technician B says that the catalytic converter must be restored to proper operation as
required by federal or regional regulations. - Answer- Both
Technician A says that cutting access windows into a part should only be done when
recommended by vehicle makers. Technician B says that cutting access windows is
considered a sectioning procedure. - Answer- Both
Technician A says that an upper A-pillar may be replaced without removing the
windshield. Technician B says that a quarter panel may require removal when replacing
a rocker panel reinforcement. - Answer- B only
Technician A says that the passenger compartment is designed to remain intact to
provide a safe space for the vehicle occupants. Technician B says that holes may be
designed into a rail to strengthen the part. - Answer- A only
The picture above represents which type of damage? Picture of a frame - Answer- side
away
Technician A says that cracked composite radiator core supports should be repaired
with a fiber mat and adhesive. Technician B says that cracked magnesium radiator core
supports should be replaced. - Answer- B only
, Technician A says that an example of direct damage is a buckle in the roof caused by
collision energy traveling through the vehicle structure. Technician B says that an
example of mass inertia damage is damage caused to the front panel of a pickup truck
bed by an unsecured object sliding forward. - Answer- B only
The illustration above shows: picture of car with red underneath - Answer- : Datum
plane
Which of these types of steel usually require replacement when damaged - Answer-
UHSS
Technician A says that the process of forming a part causes the part to become work
hardened. Technician B says that excessive work hardening may cause a part to crack.
- Answer- Both
Technician A says that an inner reinforcement made from UHSS may be straightened
with heat. Technician B says that some vehicle makers have procedures for sectioning
UHSS parts. - Answer- B only
Technician A says that hoods are designed with reinforcements to prevent folding
during a collision. Technician B says that some hoods are made from reinforced plastic.
- Answer- B only
Technician A says that hazard lamps use the same bulbs as turn signal lamps. Tech B
says that front turn signal lamps are red. - Answer- A only
The side area of the door shell that is concealed when the door is closed is called the -
Answer- doorjamb
How is a pickup truck box assembly attached to the frame? - Answer- Bolted
An out-of-level center section is often an indication of which type of damage - Answer-
Twist
Technician A says that the trunk floor may affect how a rear rail collapses. Technician B
says that the trunk floor may close out a structural hat channel. - Answer- Both
Technician A says that the windshield helps manage collision energy. Technician B
says that the windshield may deflect the driver airbag. - Answer- A only
Crush boxes are generally attached to which of these parts? - Answer- Lower front rail
Which of these typically requires replacement when damaged - Answer- Engine
WITH VERIFIED ANSWERS LATEST
UPDATE
Technician A says that a highly formed piece of sheet metal can be bent further than a
flat piece of sheet metal. Technician B says that the shape of the part may affect
whether kink vs. bend can be applied. - Answer- B only
Which of the following is true about rear lamp inspection? - Answer- To perform a
complete analysis, it may be necessary to partially disassemble the lamp assembly
Technician A says that contaminated fuel tanks should be replaced. Technician B says
that an incorrect fuel level reading could be due to the fuel pump and sending unit
shifting during a collision. B o - Answer- B only
Technician A says that exhaust soot on underbody parts may indicate a leak.
Technician B says that the catalytic converter must be restored to proper operation as
required by federal or regional regulations. - Answer- Both
Technician A says that cutting access windows into a part should only be done when
recommended by vehicle makers. Technician B says that cutting access windows is
considered a sectioning procedure. - Answer- Both
Technician A says that an upper A-pillar may be replaced without removing the
windshield. Technician B says that a quarter panel may require removal when replacing
a rocker panel reinforcement. - Answer- B only
Technician A says that the passenger compartment is designed to remain intact to
provide a safe space for the vehicle occupants. Technician B says that holes may be
designed into a rail to strengthen the part. - Answer- A only
The picture above represents which type of damage? Picture of a frame - Answer- side
away
Technician A says that cracked composite radiator core supports should be repaired
with a fiber mat and adhesive. Technician B says that cracked magnesium radiator core
supports should be replaced. - Answer- B only
, Technician A says that an example of direct damage is a buckle in the roof caused by
collision energy traveling through the vehicle structure. Technician B says that an
example of mass inertia damage is damage caused to the front panel of a pickup truck
bed by an unsecured object sliding forward. - Answer- B only
The illustration above shows: picture of car with red underneath - Answer- : Datum
plane
Which of these types of steel usually require replacement when damaged - Answer-
UHSS
Technician A says that the process of forming a part causes the part to become work
hardened. Technician B says that excessive work hardening may cause a part to crack.
- Answer- Both
Technician A says that an inner reinforcement made from UHSS may be straightened
with heat. Technician B says that some vehicle makers have procedures for sectioning
UHSS parts. - Answer- B only
Technician A says that hoods are designed with reinforcements to prevent folding
during a collision. Technician B says that some hoods are made from reinforced plastic.
- Answer- B only
Technician A says that hazard lamps use the same bulbs as turn signal lamps. Tech B
says that front turn signal lamps are red. - Answer- A only
The side area of the door shell that is concealed when the door is closed is called the -
Answer- doorjamb
How is a pickup truck box assembly attached to the frame? - Answer- Bolted
An out-of-level center section is often an indication of which type of damage - Answer-
Twist
Technician A says that the trunk floor may affect how a rear rail collapses. Technician B
says that the trunk floor may close out a structural hat channel. - Answer- Both
Technician A says that the windshield helps manage collision energy. Technician B
says that the windshield may deflect the driver airbag. - Answer- A only
Crush boxes are generally attached to which of these parts? - Answer- Lower front rail
Which of these typically requires replacement when damaged - Answer- Engine
