MSSC Quality post test Questions And Answers
Verified 100% Correct
1. A histogram with bimodal distribution is an indication of - ANSWER Two
distinct datasets
2. The chart that will plot the average value of a subgroup is the - CORRECT
ANSWER X Bar
43.Geometric dimensioning and tolerancing refers to - ANSWER limits of
size (tolerancing)
4. The "ECN" acronym stands for - ANSWER Engineering change notice
5. A digital caliper would be connected to a PCin order to: - ANSWER D.
Collect SPC data
7 Companies use a "quality metric" to: - ANSWER Establish
measurements for process improvements
6. Problem analysis tools include - ANSWER Brainstorming
Cause and effect diagrams
Root cause analysis
8. A "third party" audit organization is defined as: - ANSWER D. Someone
outside the organization
9. An audit checklist is used to: - ANSWER Obtain relatively uniform
results
10. A quality audit is performed in order to - ANSWER Ensure that
processes and procedures are followed
X Bar: - ANSWER A chart that will plot the average value of a subgroup
51. Calibration - - ANSWER Adjusting a device to a standard.
53. Histogram - - ANSWER A type of graph that shows the frequency of
distribution of measured data.
, 54. ISO 9000 - - ANSWER A family of international standards that apply to
the design and implementation of quality systems
55. Run Chart - - ANSWER A chart that tracks a measured value over time.
56. PDCA cycle- - ANSWER A simple process for implementing continuous
improvement changes in four steps: plan, do, check, and act.
57. What type of feature is parallel to the surface being dimensioned? - CORRECT
ANSWER Dimension line
58. What part of an assembly fastener is designed to protect the threads _____. -
ANSWER Shank
60. One inch is equal to _______. - ANSWER 25.4mm
59. Metals treated by ____ processes to become soft. - ANSWER
Annealing
61. A _______ is a measurement tool that measures part dimensions by indicating the
amount of distance its probe moves when placed against the part. - CORRECT
ANSWER Dial indicator
62. The due date for calibration must appear on the calibration label of ____. -
ANSWER . Measurement & test equipment.
63. What are the two types of assembly drawings? - ANSWER Detailed and
exploded
64. Section lines on a blueprint indicate ______. - ANSWER A surface that
has been cut
66. Which of the following is not one of the six rules for the dimensioning an object? -
ANSWER . Dimension hidden lines
65. What type of hole is shown in the picture? - ANSWER b. Counterbore
67. If 200 parts are sampled from 3000 products, what is the sampling rate? -
ANSWER 6.7 percent
68. Parts are inspected _______ to make sure the typical characteristics of a produced
part are found. - ANSWER Randomly
69. If a sampling plan required 5% of the parts to be inspected in 1000 parts? -
Verified 100% Correct
1. A histogram with bimodal distribution is an indication of - ANSWER Two
distinct datasets
2. The chart that will plot the average value of a subgroup is the - CORRECT
ANSWER X Bar
43.Geometric dimensioning and tolerancing refers to - ANSWER limits of
size (tolerancing)
4. The "ECN" acronym stands for - ANSWER Engineering change notice
5. A digital caliper would be connected to a PCin order to: - ANSWER D.
Collect SPC data
7 Companies use a "quality metric" to: - ANSWER Establish
measurements for process improvements
6. Problem analysis tools include - ANSWER Brainstorming
Cause and effect diagrams
Root cause analysis
8. A "third party" audit organization is defined as: - ANSWER D. Someone
outside the organization
9. An audit checklist is used to: - ANSWER Obtain relatively uniform
results
10. A quality audit is performed in order to - ANSWER Ensure that
processes and procedures are followed
X Bar: - ANSWER A chart that will plot the average value of a subgroup
51. Calibration - - ANSWER Adjusting a device to a standard.
53. Histogram - - ANSWER A type of graph that shows the frequency of
distribution of measured data.
, 54. ISO 9000 - - ANSWER A family of international standards that apply to
the design and implementation of quality systems
55. Run Chart - - ANSWER A chart that tracks a measured value over time.
56. PDCA cycle- - ANSWER A simple process for implementing continuous
improvement changes in four steps: plan, do, check, and act.
57. What type of feature is parallel to the surface being dimensioned? - CORRECT
ANSWER Dimension line
58. What part of an assembly fastener is designed to protect the threads _____. -
ANSWER Shank
60. One inch is equal to _______. - ANSWER 25.4mm
59. Metals treated by ____ processes to become soft. - ANSWER
Annealing
61. A _______ is a measurement tool that measures part dimensions by indicating the
amount of distance its probe moves when placed against the part. - CORRECT
ANSWER Dial indicator
62. The due date for calibration must appear on the calibration label of ____. -
ANSWER . Measurement & test equipment.
63. What are the two types of assembly drawings? - ANSWER Detailed and
exploded
64. Section lines on a blueprint indicate ______. - ANSWER A surface that
has been cut
66. Which of the following is not one of the six rules for the dimensioning an object? -
ANSWER . Dimension hidden lines
65. What type of hole is shown in the picture? - ANSWER b. Counterbore
67. If 200 parts are sampled from 3000 products, what is the sampling rate? -
ANSWER 6.7 percent
68. Parts are inspected _______ to make sure the typical characteristics of a produced
part are found. - ANSWER Randomly
69. If a sampling plan required 5% of the parts to be inspected in 1000 parts? -
