TESTOUT NETWORK PRO ACTUAL EXAM
PAPER 2026 QUESTIONS WITH ANSWERS
GRADED A+
◍ select the statement that best describes a broadcast storm. Answer:A
Broadcast storm occurs when there are so many broadcast messages on
the network that they approach or exceed the network bandwidth..
◍ Which of the following solutions would you implement to eliminate
switching loops? Answer:spanning tree
◍ You manage a network that uses a single switch. All ports within your
buildings connect through he single switch . Which feature should you
implement? Answer:VLANs
◍ You manage a network that uses multiple switches. You want to
provide multiple paths between switches so that if one link goes down,
an alternate path is available.
Which feature should your switch support? Answer:spanning tree
◍ You run a small network for your business that has a single router
connected to the internet and a single switch. You keep sensitive doc.
,What should you use for this situation? Answer:VLAN
◍ You manage a single subnet with three switches. The switches are
connected to provide redundant paths between the switches.
Which feature prevents switching loops and ensures there is only a
single active patch between any two switches? Answer:Spanning tree
◍ Which feature prevents switching loops and ensures there is only a
single active path between any two switches? Answer:spanning trees
◍ A user reports that network access from her workstation is very slow.
The problem does not seem to be affecting any other users.
Which of the following conditions is the most likely cause?
Answer:Duplex mismatch
◍ You manage a local area network with several switches. A new
employee has started today so you connect her workstation to a switch
port.
Which of the following is the most likely cause of the problem?
Answer:Incorrect VLAN assignment
,◍ You manage a network with multiple switches. You find that your
switches are experiencing heavy broadcast storms.
Which of the following will help reduce the effects of a broadcast storm?
Answer:Enable spanning tree on the switches
◍ Which of the following solutions would you implement to eliminate
switching loops? Answer:spanning tree
◍ While viewing the status of the interfaces on a Cisco switch, you see
abnormally large of oversized ethernet frames being received on one
interface. This interface is connected to a workstation located on the 2nd
floor.
What could be causing this to happen? Answer:The workstation's
network board is jabbering
◍ The network board in a workstation is currently configured as
follows: Answer:show running-config interface
show interface
◍ You manage a single subnet with three switches. The switches are
connected to provide redundant paths between the switches.
Which feature allows the switches to pass VLAN traffic between the
switches? Answer:Trunking
, ◍ You manage a network with two switches. The switches are connected
together through their Gigabit Ethernet uplink ports.
You define VLAN 1 and VLAN 2 on each switch. A device on the first
switch in VLAN 1 needs to communicate with a device on the second
switch also in VLAN 1.
What should you configure to allow communication between these two
devices through the switches? Answer:Trunking
◍ When configuring VLANs on a switch, what type of switch ports are
members of all VLANs defined on the switch? Answer:Trunk Ports
◍ Computers A and B are on the same VLAN and are separated by two
switches, as shown in the exhibit. Computer A sends a Fram to
Computer B.
Which of the following best describes the composition of the frame as it
travels from A to B? Answer:Computer A sends a normal frame. The
first switch appends a VLAN ID to the frame. The second switch
removes the VLAN ID before forwarding it to Computer B.
◍ Which of the following statements accurately describes a VLAN ID?
Answer:Switches append a VLAN ID to the header of each frame to
identify the virtual network to which it belongs.
PAPER 2026 QUESTIONS WITH ANSWERS
GRADED A+
◍ select the statement that best describes a broadcast storm. Answer:A
Broadcast storm occurs when there are so many broadcast messages on
the network that they approach or exceed the network bandwidth..
◍ Which of the following solutions would you implement to eliminate
switching loops? Answer:spanning tree
◍ You manage a network that uses a single switch. All ports within your
buildings connect through he single switch . Which feature should you
implement? Answer:VLANs
◍ You manage a network that uses multiple switches. You want to
provide multiple paths between switches so that if one link goes down,
an alternate path is available.
Which feature should your switch support? Answer:spanning tree
◍ You run a small network for your business that has a single router
connected to the internet and a single switch. You keep sensitive doc.
,What should you use for this situation? Answer:VLAN
◍ You manage a single subnet with three switches. The switches are
connected to provide redundant paths between the switches.
Which feature prevents switching loops and ensures there is only a
single active patch between any two switches? Answer:Spanning tree
◍ Which feature prevents switching loops and ensures there is only a
single active path between any two switches? Answer:spanning trees
◍ A user reports that network access from her workstation is very slow.
The problem does not seem to be affecting any other users.
Which of the following conditions is the most likely cause?
Answer:Duplex mismatch
◍ You manage a local area network with several switches. A new
employee has started today so you connect her workstation to a switch
port.
Which of the following is the most likely cause of the problem?
Answer:Incorrect VLAN assignment
,◍ You manage a network with multiple switches. You find that your
switches are experiencing heavy broadcast storms.
Which of the following will help reduce the effects of a broadcast storm?
Answer:Enable spanning tree on the switches
◍ Which of the following solutions would you implement to eliminate
switching loops? Answer:spanning tree
◍ While viewing the status of the interfaces on a Cisco switch, you see
abnormally large of oversized ethernet frames being received on one
interface. This interface is connected to a workstation located on the 2nd
floor.
What could be causing this to happen? Answer:The workstation's
network board is jabbering
◍ The network board in a workstation is currently configured as
follows: Answer:show running-config interface
show interface
◍ You manage a single subnet with three switches. The switches are
connected to provide redundant paths between the switches.
Which feature allows the switches to pass VLAN traffic between the
switches? Answer:Trunking
, ◍ You manage a network with two switches. The switches are connected
together through their Gigabit Ethernet uplink ports.
You define VLAN 1 and VLAN 2 on each switch. A device on the first
switch in VLAN 1 needs to communicate with a device on the second
switch also in VLAN 1.
What should you configure to allow communication between these two
devices through the switches? Answer:Trunking
◍ When configuring VLANs on a switch, what type of switch ports are
members of all VLANs defined on the switch? Answer:Trunk Ports
◍ Computers A and B are on the same VLAN and are separated by two
switches, as shown in the exhibit. Computer A sends a Fram to
Computer B.
Which of the following best describes the composition of the frame as it
travels from A to B? Answer:Computer A sends a normal frame. The
first switch appends a VLAN ID to the frame. The second switch
removes the VLAN ID before forwarding it to Computer B.
◍ Which of the following statements accurately describes a VLAN ID?
Answer:Switches append a VLAN ID to the header of each frame to
identify the virtual network to which it belongs.
