1|Page
PIPEFITTER NCEER CERTIFICATION EXAM WITH
ACTUAL QUESTIONS AND CORRECT VERIFIED
ANSWERS/ALREADY GRADED A+ 100%
GUARANTEED TO PASS CONCEPTS(ALL WHAT
YOU NEED) LATEST EDITION
To what position does a pneumatic control valve that
loses its air supply return? - .....ANSWER ...✔✔
Normally closed
In MOST instances, what is stamped or forged on the
side of valves, fittings, and flanges? - .....ANSWER
...✔✔ Types of material, size, and pressure ratings
Expansion loops are NOT made with these types of
fittings: - .....ANSWER ...✔✔ Butt Weld
If a pipe is 36' - 8 & 3/4" from the centerline of one
elbow on one end to the center of a tee in the pipeline
and center of the elbow on one end to the center of the
elbow to the other end? - .....ANSWER ...✔✔ 1/2
wall thickness of the pipe
, 2|Page
All piping and piping components are identified by
what international identification system? - .....ANSWER
...✔✔ ASME
A slip on flange should extend, whichever is greater, at
least 3/8" or: - .....ANSWER ...✔✔ 1/2 the wall
thickness of the pipe
Dry wash is a form of - .....ANSWER ...✔✔ cold
springing
Which drawing gives enough info to be able to
fabricate a pipe run? - .....ANSWER ...✔✔ P & ID
When using shoring to support walls in an excavation,
which of the following would NOT be used? -
.....ANSWER ...✔✔ Soil Anchor
The inlet of a CORRECTLY installed orifice plate will be:
- .....ANSWER ...✔✔ beveled toward the flow
What is the decimal sum of 1/2" + 3/8" + 0.625? -
.....ANSWER ...✔✔ 1.500 inches
PIPEFITTER NCEER CERTIFICATION EXAM WITH
ACTUAL QUESTIONS AND CORRECT VERIFIED
ANSWERS/ALREADY GRADED A+ 100%
GUARANTEED TO PASS CONCEPTS(ALL WHAT
YOU NEED) LATEST EDITION
To what position does a pneumatic control valve that
loses its air supply return? - .....ANSWER ...✔✔
Normally closed
In MOST instances, what is stamped or forged on the
side of valves, fittings, and flanges? - .....ANSWER
...✔✔ Types of material, size, and pressure ratings
Expansion loops are NOT made with these types of
fittings: - .....ANSWER ...✔✔ Butt Weld
If a pipe is 36' - 8 & 3/4" from the centerline of one
elbow on one end to the center of a tee in the pipeline
and center of the elbow on one end to the center of the
elbow to the other end? - .....ANSWER ...✔✔ 1/2
wall thickness of the pipe
, 2|Page
All piping and piping components are identified by
what international identification system? - .....ANSWER
...✔✔ ASME
A slip on flange should extend, whichever is greater, at
least 3/8" or: - .....ANSWER ...✔✔ 1/2 the wall
thickness of the pipe
Dry wash is a form of - .....ANSWER ...✔✔ cold
springing
Which drawing gives enough info to be able to
fabricate a pipe run? - .....ANSWER ...✔✔ P & ID
When using shoring to support walls in an excavation,
which of the following would NOT be used? -
.....ANSWER ...✔✔ Soil Anchor
The inlet of a CORRECTLY installed orifice plate will be:
- .....ANSWER ...✔✔ beveled toward the flow
What is the decimal sum of 1/2" + 3/8" + 0.625? -
.....ANSWER ...✔✔ 1.500 inches
