ICC Structural Steel Save
Terms in this set (110)
Adjustable items such as lintels, within 3/8 inch of the specified location
curb angles and mullions are
considered properly placed
when they are
After time and exposure of the will produce results of questionable accuracy
bolted joints, the use of torque
methods:
, within 1/4 and 1/2 inch tolerance from one anchor bolt group to
Anchor rod groups must be set:
the next
Anchor rods ( previously and within 1/8 inch center to center of one another
commonly called anchor bolts)
within a given anchor rod group
should be set :
for slip critical joints, or for pretensioned joints when carrying
Arbitration of disputes is
applied tension and for joints inspected using the methods of
applicable only:
sections 9.2 and 9.3
within an short period of time following installation of the bolts
Arbitration of disputes must
take place:
16 .2 -63
A bolt calibration device is slip- critical joints and pre-tensioned joints are specified
required for pre-installation
testing whenever: AISC 16 2-47
Braces and ties for lighting designated seismic systems
systems and sprinkler lines
suspended from ceilings are
examples of;
Column positions may be the column is adjacent to an elevator shaft and exterior coumn
further restricted beyond just
plumbness when
, A column splice, either welded 1/16
or bolted, is permitted to have
a gap of ______ between the
upper and lower shafts, without
repair or shimming
Continuous monitoring of bolt if the turn of method is used without match-marking, and if the
installation of pretensioned calibrated wrench method is used
joints is required
the inspector is onsite observing the work requiring special
Continuous special inspection
inspection( present when and where the work to be inspected
means
is being performed)
Direct tension indicators (DTI's) ASTM F959
are addressed in which ASTM
standard AISC 16 2.14
Except for certain types and during the welding operations
sizes of welds, inspection of
structural welding is to be done
structural, load bearing assemblies of materials assembled
A fabricated item is
prior to the installation in the building
Floor member elevation is if the ends of the beam or girder are within elevation tolerances
considered acceptable where attached to the supporting members
For arbitration of disputes, the must be determined by testing representative bolts in a bolt
inspection torque must be: calibration device
Terms in this set (110)
Adjustable items such as lintels, within 3/8 inch of the specified location
curb angles and mullions are
considered properly placed
when they are
After time and exposure of the will produce results of questionable accuracy
bolted joints, the use of torque
methods:
, within 1/4 and 1/2 inch tolerance from one anchor bolt group to
Anchor rod groups must be set:
the next
Anchor rods ( previously and within 1/8 inch center to center of one another
commonly called anchor bolts)
within a given anchor rod group
should be set :
for slip critical joints, or for pretensioned joints when carrying
Arbitration of disputes is
applied tension and for joints inspected using the methods of
applicable only:
sections 9.2 and 9.3
within an short period of time following installation of the bolts
Arbitration of disputes must
take place:
16 .2 -63
A bolt calibration device is slip- critical joints and pre-tensioned joints are specified
required for pre-installation
testing whenever: AISC 16 2-47
Braces and ties for lighting designated seismic systems
systems and sprinkler lines
suspended from ceilings are
examples of;
Column positions may be the column is adjacent to an elevator shaft and exterior coumn
further restricted beyond just
plumbness when
, A column splice, either welded 1/16
or bolted, is permitted to have
a gap of ______ between the
upper and lower shafts, without
repair or shimming
Continuous monitoring of bolt if the turn of method is used without match-marking, and if the
installation of pretensioned calibrated wrench method is used
joints is required
the inspector is onsite observing the work requiring special
Continuous special inspection
inspection( present when and where the work to be inspected
means
is being performed)
Direct tension indicators (DTI's) ASTM F959
are addressed in which ASTM
standard AISC 16 2.14
Except for certain types and during the welding operations
sizes of welds, inspection of
structural welding is to be done
structural, load bearing assemblies of materials assembled
A fabricated item is
prior to the installation in the building
Floor member elevation is if the ends of the beam or girder are within elevation tolerances
considered acceptable where attached to the supporting members
For arbitration of disputes, the must be determined by testing representative bolts in a bolt
inspection torque must be: calibration device
