SACA Certification C-101 2025 NEWEST EXAM COMPLETE
QUESTIONS AND CORRECT DETAILED ANSWERS (VERIFIED
ANSWERS) |ALREADY GRADED A+||BRAND NEW!!Ivy Tech
Community College \INDT 113
1. Shut down the equipment What are the 5 steps of electrical Lockout/tagout
2. Connect Hasp
3. Attach Lock
4. Add Tag
5. Test Start Equipment
Falls Which of the following is a common cause of workplace death?
Hazard assessment The process of identifying potential hazards in the workplace is
known as a ________________________________________.
An injury is defined as physical harm to the body
TRUE that happens as a result of exposure to some
form of energy that exceeds the body's tolerance.
Is this statement TRUE or FALSE?
Shut down their machines and In the event of an evacuation alarm, employees should _.
leave the building
After exposure to most chemicals the eyes should be flushed
15
continuously for
_ ___ minutes.
Thickeners Grease is made from a liquid lubricant with what added to it to
make it semi-solid?
What does the GHS hazardous material classification
Pictograms
systems use to identify the danger of a material?
16 Every Safety Data Sheet must follow the same format that has
_________________________________________ sections.
SDS Safe handling procedures of chemicals are found in the _.
_ ___ is a system that rotates chemical stock to ensure they are
First in, first out
used within their
shelf life.
Explosive An orange DOT label indicates the material is _.
, Before shipping a hazardous material, review the , which
DOT Hazardous Materials
provides directions
Table
for packaging, labels, UN ID, and required paperwork for
shipment.
Educating employees on fire The first step in fire and electrical safety is _.
hazards and prevention
35 feet (10.6 meters) When welding, keep combustible material at least away from the
area.
Monthly OSHA requires inspections of fire extinguishers.
Standard operating procedure A safe work place begins by designing in safety by creating a(n)
__________________________________________ _.
OSHA requires elevated work surfaces to have guards if the
4 feet (1.2 meters)
surface is _____________________________________ above
ground.
Repetitive motion injuries A consequence of work stations with poorly designed
ergonomics is ________________________________ _.
Rotate tasks among A common ergonomic practice to reduce injuries is to _.
employees
Which classification of hardhat is designed for use in
Bump Caps
areas of low clearance and provides minimal impact
resistance or protection from electrical hazards?
Foot protection What protection does a metatarsal guard provide?
Power Tools operated electrically or by pneumatic power are classified
as ___________________________________________ tools.
Screwdrivers The leading cause of accidents with hand tools is improper use of
___________________________________________ _.
Reading the cylinder label The contents of a gas cylinder are only determined by _.
Pallet jack A____ is a manually operated forklift.
Working Load Limit (WLL) Lifting equipment must be operated within its _.
Daily OSHA requires forklifts be inspected _.
Box end wrench What is best wrench to use to loosen a bolt?
Hex wrench What wrench is used to tighten a socket head cap screw?
A____ is an important measuring tool in manufacturing because it
Machinist's rule
can easily be
carried in a pocket and provides quick measurements and
approximate dimensions.
Width, height, and depth Dimensional measurement determines physical dimensions such as
_____________________________________________.
Two systems of dimensional measurement used in
US customary system
manufacturing are the SI Metric System and the _.
25.4 convert inches to millimeters, multiply the inches by _.
QUESTIONS AND CORRECT DETAILED ANSWERS (VERIFIED
ANSWERS) |ALREADY GRADED A+||BRAND NEW!!Ivy Tech
Community College \INDT 113
1. Shut down the equipment What are the 5 steps of electrical Lockout/tagout
2. Connect Hasp
3. Attach Lock
4. Add Tag
5. Test Start Equipment
Falls Which of the following is a common cause of workplace death?
Hazard assessment The process of identifying potential hazards in the workplace is
known as a ________________________________________.
An injury is defined as physical harm to the body
TRUE that happens as a result of exposure to some
form of energy that exceeds the body's tolerance.
Is this statement TRUE or FALSE?
Shut down their machines and In the event of an evacuation alarm, employees should _.
leave the building
After exposure to most chemicals the eyes should be flushed
15
continuously for
_ ___ minutes.
Thickeners Grease is made from a liquid lubricant with what added to it to
make it semi-solid?
What does the GHS hazardous material classification
Pictograms
systems use to identify the danger of a material?
16 Every Safety Data Sheet must follow the same format that has
_________________________________________ sections.
SDS Safe handling procedures of chemicals are found in the _.
_ ___ is a system that rotates chemical stock to ensure they are
First in, first out
used within their
shelf life.
Explosive An orange DOT label indicates the material is _.
, Before shipping a hazardous material, review the , which
DOT Hazardous Materials
provides directions
Table
for packaging, labels, UN ID, and required paperwork for
shipment.
Educating employees on fire The first step in fire and electrical safety is _.
hazards and prevention
35 feet (10.6 meters) When welding, keep combustible material at least away from the
area.
Monthly OSHA requires inspections of fire extinguishers.
Standard operating procedure A safe work place begins by designing in safety by creating a(n)
__________________________________________ _.
OSHA requires elevated work surfaces to have guards if the
4 feet (1.2 meters)
surface is _____________________________________ above
ground.
Repetitive motion injuries A consequence of work stations with poorly designed
ergonomics is ________________________________ _.
Rotate tasks among A common ergonomic practice to reduce injuries is to _.
employees
Which classification of hardhat is designed for use in
Bump Caps
areas of low clearance and provides minimal impact
resistance or protection from electrical hazards?
Foot protection What protection does a metatarsal guard provide?
Power Tools operated electrically or by pneumatic power are classified
as ___________________________________________ tools.
Screwdrivers The leading cause of accidents with hand tools is improper use of
___________________________________________ _.
Reading the cylinder label The contents of a gas cylinder are only determined by _.
Pallet jack A____ is a manually operated forklift.
Working Load Limit (WLL) Lifting equipment must be operated within its _.
Daily OSHA requires forklifts be inspected _.
Box end wrench What is best wrench to use to loosen a bolt?
Hex wrench What wrench is used to tighten a socket head cap screw?
A____ is an important measuring tool in manufacturing because it
Machinist's rule
can easily be
carried in a pocket and provides quick measurements and
approximate dimensions.
Width, height, and depth Dimensional measurement determines physical dimensions such as
_____________________________________________.
Two systems of dimensional measurement used in
US customary system
manufacturing are the SI Metric System and the _.
25.4 convert inches to millimeters, multiply the inches by _.
