1|Page
NEIEP 200 Final Exam|| QUESTIONS AND CORRECT
DETAILED ANSWERS||VERIFIED EXAM!!! (VERIFIED
ANSWERS) |ALREADY GRADED A+||NEWEST EXAM!!!
You are installing rails with little distance between the
beam and rail. What type of bracket must you use? -
ANSWER-angle bracket
You must fasten a bracket to a brick wall. How do you do
it? - ANSWER-(quick bolt that bitch) use a threaded rod
and thru plate it
When installing formed guide rails, what must be done to
ensure that the guide rail is secured to the rail bracket? -
ANSWER-rail clip heel must contact the edge of the rail
You are setting up welding equipment. What is the
maximum psi that the regulator for the acetylene gas may
be adjusted to? - ANSWER-10-12 psi
You are using rollers to move a heavy elevator machine
and are approaching a corner. Which technique should
you use to maneuver around it? - ANSWER-angle front
roller gradually and continue around the corner
,2|Page
You are preparing to unload a truck at the loading dock
and the truck is 8" higher than the dock. What do you do?
- ANSWER-use a steel plate to span the gap
You just finished the surface inspection of a manila rope
you will be using for hoisting. What method should you
use to conduct an internal inspection? - ANSWER-slightly
untwist the strands
You are preparing to hoist rails and are inspecting your
manila rope. Which of the following is a good
characteristic of manila rope? - ANSWER-a light yellow
color with a silvery or pearly luster
A mechanic attaches a chainfall to a hoisting beam with a
beam clamp. What happens to the capacity of the hoisting
beam? - ANSWER-it is reduced to 50% of original capacity
You are rigging elevator equipment with a sling angle of 60
degrees. You are using a shouldered eye bolt with a
tapped 1/2" diameter hole. Once the shoulder is seated,
what is the minimum thread depth required? - ANSWER-at
least 3/4"
, 3|Page
You will be hoisting 1klbs with a single leg vertical hitch.
What will the sling load be when the load is in the air -
ANSWER-1k lbs
You must attach a wire rope to a load by creating a loop
with 3 u-bolt wire rope clips. How should the clips be
attached? - ANSWER-no nuts on a dead horse
You are using a bowline knot- what is one disadvantage of
this knot - ANSWER-is can easily loosen when not loaded
You are preparing to lift a load and need to tie the ends of
two ropes together. Which knot should you use? -
ANSWER-square
The rated load tag on a sling is 2000lbs. What does this
mean? - ANSWER-load limit that can be picked and held
You need to lift rails to the top floor of a building. With a
well wheel at the top of the hoistway, what type of rope
should you use? - ANSWER-synthetic
NEIEP 200 Final Exam|| QUESTIONS AND CORRECT
DETAILED ANSWERS||VERIFIED EXAM!!! (VERIFIED
ANSWERS) |ALREADY GRADED A+||NEWEST EXAM!!!
You are installing rails with little distance between the
beam and rail. What type of bracket must you use? -
ANSWER-angle bracket
You must fasten a bracket to a brick wall. How do you do
it? - ANSWER-(quick bolt that bitch) use a threaded rod
and thru plate it
When installing formed guide rails, what must be done to
ensure that the guide rail is secured to the rail bracket? -
ANSWER-rail clip heel must contact the edge of the rail
You are setting up welding equipment. What is the
maximum psi that the regulator for the acetylene gas may
be adjusted to? - ANSWER-10-12 psi
You are using rollers to move a heavy elevator machine
and are approaching a corner. Which technique should
you use to maneuver around it? - ANSWER-angle front
roller gradually and continue around the corner
,2|Page
You are preparing to unload a truck at the loading dock
and the truck is 8" higher than the dock. What do you do?
- ANSWER-use a steel plate to span the gap
You just finished the surface inspection of a manila rope
you will be using for hoisting. What method should you
use to conduct an internal inspection? - ANSWER-slightly
untwist the strands
You are preparing to hoist rails and are inspecting your
manila rope. Which of the following is a good
characteristic of manila rope? - ANSWER-a light yellow
color with a silvery or pearly luster
A mechanic attaches a chainfall to a hoisting beam with a
beam clamp. What happens to the capacity of the hoisting
beam? - ANSWER-it is reduced to 50% of original capacity
You are rigging elevator equipment with a sling angle of 60
degrees. You are using a shouldered eye bolt with a
tapped 1/2" diameter hole. Once the shoulder is seated,
what is the minimum thread depth required? - ANSWER-at
least 3/4"
, 3|Page
You will be hoisting 1klbs with a single leg vertical hitch.
What will the sling load be when the load is in the air -
ANSWER-1k lbs
You must attach a wire rope to a load by creating a loop
with 3 u-bolt wire rope clips. How should the clips be
attached? - ANSWER-no nuts on a dead horse
You are using a bowline knot- what is one disadvantage of
this knot - ANSWER-is can easily loosen when not loaded
You are preparing to lift a load and need to tie the ends of
two ropes together. Which knot should you use? -
ANSWER-square
The rated load tag on a sling is 2000lbs. What does this
mean? - ANSWER-load limit that can be picked and held
You need to lift rails to the top floor of a building. With a
well wheel at the top of the hoistway, what type of rope
should you use? - ANSWER-synthetic
