NICET LEVEL 1 Exam Questions and Answers with Verified
Solutions | Latest 2026 Update
Q: what is the maximum number of 14 AWG RHH conductors which can be installed in 1/2 rigid
metal conduit?
Answer:
4 wires
Q: Which of the following would be an appropriate mounting height for a pull station?
Answer:
3.5'-48" to the actuator
Q: What is the minimum flash rate for a visible notification device?
Answer:
1 flash per second
Q: What is the minimum mounting height for audible notification devices?
Answer:
90" to the top of the device
Q: What is the minimum mounting height for visible notification devices?
Answer:
Such that the entire lens is not less then 80"
Q: What is the formula for Ohm's Law
Answer:
Voltage=Current X Resistence
Q: When using your mult-meter to measure, you must:
Answer:
Put your meter in series with the circuit
Q: Waterflow devices shall be tested with that frequency?
Answer:
Semi-annually
, Q: With what frequency shall ionization smoke detectors be given a functional test?
Answer:
Annually
Q: What are the standby power requirements for a proprietary signaling system?
Answer:
24 hours in normal operation, 5 minutes in alarm
Q: Which of the following is a type of auxiliary protective signaling system?
Answer:
Shunt type
Q: Remote station signaling systems are permitted to send signals to:
Answer:
A UL listed central station A receiver located at an unlisted monitoring facility A fire department or
communications center
Q: Non-power limited fire alarm cable shall have an insulation rating of:
Answer:
600V
Q: Which of these HVAC systems would require duct detectors on supply and return?
Answer:
20,000 CFM HVAC system serving a single floor 15,000 CFM HVAC system serving 3 floors
20,000 CFM HVAC system serving 2 floors
Q: According to the IBC, which of the following use Groups require visual notification?
Answer:
Group A, E, F
Q: Digital Alarm communicator transmitters (DACT) which use call forwarding to the DACR shall
be tested with what frequency?
Answer:
Every 4 hours
Solutions | Latest 2026 Update
Q: what is the maximum number of 14 AWG RHH conductors which can be installed in 1/2 rigid
metal conduit?
Answer:
4 wires
Q: Which of the following would be an appropriate mounting height for a pull station?
Answer:
3.5'-48" to the actuator
Q: What is the minimum flash rate for a visible notification device?
Answer:
1 flash per second
Q: What is the minimum mounting height for audible notification devices?
Answer:
90" to the top of the device
Q: What is the minimum mounting height for visible notification devices?
Answer:
Such that the entire lens is not less then 80"
Q: What is the formula for Ohm's Law
Answer:
Voltage=Current X Resistence
Q: When using your mult-meter to measure, you must:
Answer:
Put your meter in series with the circuit
Q: Waterflow devices shall be tested with that frequency?
Answer:
Semi-annually
, Q: With what frequency shall ionization smoke detectors be given a functional test?
Answer:
Annually
Q: What are the standby power requirements for a proprietary signaling system?
Answer:
24 hours in normal operation, 5 minutes in alarm
Q: Which of the following is a type of auxiliary protective signaling system?
Answer:
Shunt type
Q: Remote station signaling systems are permitted to send signals to:
Answer:
A UL listed central station A receiver located at an unlisted monitoring facility A fire department or
communications center
Q: Non-power limited fire alarm cable shall have an insulation rating of:
Answer:
600V
Q: Which of these HVAC systems would require duct detectors on supply and return?
Answer:
20,000 CFM HVAC system serving a single floor 15,000 CFM HVAC system serving 3 floors
20,000 CFM HVAC system serving 2 floors
Q: According to the IBC, which of the following use Groups require visual notification?
Answer:
Group A, E, F
Q: Digital Alarm communicator transmitters (DACT) which use call forwarding to the DACR shall
be tested with what frequency?
Answer:
Every 4 hours
