1 for specific request mail
Gas CFESA Practice Test Questions and Correct
Answers | Latest Update
The purpose of a draft hood/draft diverter is_______?
A) To prevent drafts from entering the burner compartment that comes
from the power cent
hoods.
B) To prevent the combustion chamber from overheating, and allowing
air to come down the
Assignment Expert
vent pipe into the room.
Guru01 - Stuvia
C) To allow the flue to control the amount of secondary air drawn in
instead of the vent pipe,
and to prevent air from coming back down the vent into the combustion
2026
chamber
D) To allow the vent pipe to control the amount of secondary air drawn
©
into the combustion
chamber as designed by its height above the hood.
Ans: C
The two primary functions of the flue are____?
A) The remove combustion byproducts and heat from the equipment
B) To create a draft to pull in secondary air and remove the byproducts
form the combustion
chamber
C) To create a draft to keep the burners cool and remove byproducts
from the cooking area
, 2 for specific request mail
D) To remove the excessive heat to keep the burners, and cooking surface
from overheating
Ans: B
To solve unusual venting problems like negative pressure, high winds,
long vents, the installe
should use_____?
A) A larger size vent pipe
B) Vent outlets
Assignment Expert
C) Vent top turbines
Guru01 - Stuvia
D) A draft hood
Ans: D
2026
What is a bypass flame?
A) The smallest flame that will keep the burners lit after the gas
©
thermostat has reached the
temperature set point
B) A flame that is 3/8" tall after the thermostat shuts off
C) A flame left on the burner to keep the pilot form going out
D) A flame to a special part of the burner after the main burner goes off
Ans: A
The primary purpose of a vent on a regulator is to:
A) Vent leaking gas
B) Allow diaphragm movement
, 3 for specific request mail
C) Allow high pressure
D) Monitor flow
Ans: B
A properly burning infrared ceramic burner will look______?
A) Blue
B) Bright reddish orange
C) Dull red
Assignment Expert
D) Blue with a tint of orange
Guru01 - Stuvia
Ans: B
Vent lines are required on regulators above 1" and must be vented:
A) A pilot flame
2026
B) An open flame within 2 feet
©
C) A working flue or exhaust system
D) The outside atmosphere, above the snow line
Ans: D
What is the proper flame current for an ignition module?
A) Always 3 or more microamps
B) Always ¼ or more microamps
C) It depends on the module manufacturer
D) Always 2 or more microamps
Ans: C
, 4 for specific request mail
Primary air is the air______?
A) That surrounds the burner
B) That enters the burner though the venture
C) Is the air that is vented through the exhaust system
D) That must always have a pressure greater than the incoming gas
pressure
Ans: B
Assignment Expert
Every time a gas fired convection oven shuts off the gas flow to the
burners there is a loud pop.
Guru01 - Stuvia
The oven is rated for and using LP gas. The noise is called_____, and can
be reduced by____ the
burner air shutters more.
2026
A) Extinction pop, opening
©
B) Delayed ignition, closing
C) Delayed ignition, opening
D) Extinction pop and by closing
Ans: D
If a leak develops in an LP gas line, where is the gas likely to go?
A) Out the exhaust system
B) To the lowest level in the room
C) Up to the ceiling area
D) Out of the kitchen under the door
Gas CFESA Practice Test Questions and Correct
Answers | Latest Update
The purpose of a draft hood/draft diverter is_______?
A) To prevent drafts from entering the burner compartment that comes
from the power cent
hoods.
B) To prevent the combustion chamber from overheating, and allowing
air to come down the
Assignment Expert
vent pipe into the room.
Guru01 - Stuvia
C) To allow the flue to control the amount of secondary air drawn in
instead of the vent pipe,
and to prevent air from coming back down the vent into the combustion
2026
chamber
D) To allow the vent pipe to control the amount of secondary air drawn
©
into the combustion
chamber as designed by its height above the hood.
Ans: C
The two primary functions of the flue are____?
A) The remove combustion byproducts and heat from the equipment
B) To create a draft to pull in secondary air and remove the byproducts
form the combustion
chamber
C) To create a draft to keep the burners cool and remove byproducts
from the cooking area
, 2 for specific request mail
D) To remove the excessive heat to keep the burners, and cooking surface
from overheating
Ans: B
To solve unusual venting problems like negative pressure, high winds,
long vents, the installe
should use_____?
A) A larger size vent pipe
B) Vent outlets
Assignment Expert
C) Vent top turbines
Guru01 - Stuvia
D) A draft hood
Ans: D
2026
What is a bypass flame?
A) The smallest flame that will keep the burners lit after the gas
©
thermostat has reached the
temperature set point
B) A flame that is 3/8" tall after the thermostat shuts off
C) A flame left on the burner to keep the pilot form going out
D) A flame to a special part of the burner after the main burner goes off
Ans: A
The primary purpose of a vent on a regulator is to:
A) Vent leaking gas
B) Allow diaphragm movement
, 3 for specific request mail
C) Allow high pressure
D) Monitor flow
Ans: B
A properly burning infrared ceramic burner will look______?
A) Blue
B) Bright reddish orange
C) Dull red
Assignment Expert
D) Blue with a tint of orange
Guru01 - Stuvia
Ans: B
Vent lines are required on regulators above 1" and must be vented:
A) A pilot flame
2026
B) An open flame within 2 feet
©
C) A working flue or exhaust system
D) The outside atmosphere, above the snow line
Ans: D
What is the proper flame current for an ignition module?
A) Always 3 or more microamps
B) Always ¼ or more microamps
C) It depends on the module manufacturer
D) Always 2 or more microamps
Ans: C
, 4 for specific request mail
Primary air is the air______?
A) That surrounds the burner
B) That enters the burner though the venture
C) Is the air that is vented through the exhaust system
D) That must always have a pressure greater than the incoming gas
pressure
Ans: B
Assignment Expert
Every time a gas fired convection oven shuts off the gas flow to the
burners there is a loud pop.
Guru01 - Stuvia
The oven is rated for and using LP gas. The noise is called_____, and can
be reduced by____ the
burner air shutters more.
2026
A) Extinction pop, opening
©
B) Delayed ignition, closing
C) Delayed ignition, opening
D) Extinction pop and by closing
Ans: D
If a leak develops in an LP gas line, where is the gas likely to go?
A) Out the exhaust system
B) To the lowest level in the room
C) Up to the ceiling area
D) Out of the kitchen under the door
