ICC Bolting EXAM (updated 2026) Questions & Answers | With 100%
Correct Answers graded A+ Guaranteed Pass!!!!!!
According to the IBC, the "blank" is to hire the special inspector. - (answer)owner or owners agent. 2009
IBC Section 1704.1
According to the IBC, the "blank" is the responsible for the approval of a person's qualifications to act as
a special inspector. - (answer)code official. 2009 IBC, Section 1704.1
According to the IBC, discrepancy corrections are made known to the building official by: - (answer)final
report. 2009 IBC, Section1704.1.2
When is the code official to be made aware of a discrepancy found during a special inspection? -
(answer)If it is not corrected by the contractor. 2009 IBC, Section 1704.1.2
According to the Model Program for Special Inspection, the special inspector is to document work that is
nonconforming: - (answer)In a written report - Section II B 4 - Model Programs
According to the Model Program for Special Inspection, the special inspector is to prepare written report
of inspection: - (answer)After each inspection visit - Section II B 5 - Model Programs
According to the Model Program for Special Inspection, which of the following items does not need to
be included in each inspection report? - (answer)Description of discussions with the contractor - Section
B 5 - Model Programs
According to the Specification for Structural Joints using high strength bolts, the nominal diameter of
standard bolt holes shall be how much larger than the nominal bolt diameter? - (answer)1/16 inch -
Specification for Structural Joints Table 3.1
,ICC Bolting EXAM (updated 2026) Questions & Answers | With 100%
Correct Answers graded A+ Guaranteed Pass!!!!!!
Discrepancies in the work shall be brought to the immediate attention of the "blank" for corrective
action. - (answer)the contractor - 2009 IBC, Section 1704.1.2.
The special inspector shall furnish inspection reports to the "blank" and to the "blank"? -
(answer)Building Official and Registered Design professional
The special inspector shall provide continuos inspection of: - (answer)Single-pass fillet welds greater
than 5/16 inch in size - 2099 IBC, Table 1704.3, Item 5.3
The special inspections required by this code are not required where the work is done on the premise of
a? - (answer)Approved fabricator - 2009 IBC, Section 1704.2.2
The special inspection of the steel fabrication process shall not be required where the fabricator does
not perform any? - (answer)heating operations - 2009 IBC, Section 1704.3, Exceptions # 1
According to the Specifications for Structural Steel Buildings, ASTM Standard "blank" is to be used for
the material test for steel sheets. - (answer)A568 - Section A31, Specifications for Structural Steel
Buildings
According to the Specifications for Structural Steel Buildings, the "blank" conducts the material tests for
identification of the structural steel. - (answer)Fabricator or Testing Laboratory - Section A31,
Specifications for Structural Steel Buildings.
According to the Specifications for Structural Steel Buildings, which of the following steel members are
allowed to be unidentified steel? - (answer)Unimportant members, where their physical properties and
weldability would not affect the structure strength - Section A31b, Specifications for Structural Steel
Buildings
, ICC Bolting EXAM (updated 2026) Questions & Answers | With 100%
Correct Answers graded A+ Guaranteed Pass!!!!!!
According to the Code of Standard Practice for Steel Buildings and Bridges, how is steel of special
material to be identified? - (answer)It is marked by the supplier - Section 5.1.1, Code of Standard
Practice for Steel Buildings and Bridges
According to the Code of Standard Practice for Steel Buildings and Bridges, how are fabricators stock
steel material identified? - (answer)Certified mill test reports - Section 5.2.2 - Code of Standard Practice
for Steel Buildings and Bridges
According to the Specification for Structural Steel Buildings, what ASTM Standard would apply to a
sample for structural steel pipe? - (answer)A53 - Section A31a - Specification for Structural Steel
Buildings
According to the Code of Standard Practice for Steel Buildings and Bridges, the number of samples
required to be tested for structural steel is: - (answer)The number specified by the ASTM specification -
Section 5.1.1 - Code of Standard Practice for Steel Buildings and Bridges
According to the Specification for Structural Steel Buildings, which ASTM standard would apply to a
sample for structural steel plates? - (answer)A36, A283, and A242 - Section A31a - Specification for
Structural Steel Buildings
According to the Specification for Structural Steel Buildings, "blank" tests are required for samples for
built-up sections consisting of plates over 2 inches in thickness. - (answer)Charpy V-notch testing -
Section A31d, Specification for Structural Steel Buildings
According to the Specification for Structural Steel Buildings, ASTM standard "blank" would apply to a
sample for structural steel bars. - (answer)A36, A529, and A572 - Specification for Structural Steel
Buildings
Correct Answers graded A+ Guaranteed Pass!!!!!!
According to the IBC, the "blank" is to hire the special inspector. - (answer)owner or owners agent. 2009
IBC Section 1704.1
According to the IBC, the "blank" is the responsible for the approval of a person's qualifications to act as
a special inspector. - (answer)code official. 2009 IBC, Section 1704.1
According to the IBC, discrepancy corrections are made known to the building official by: - (answer)final
report. 2009 IBC, Section1704.1.2
When is the code official to be made aware of a discrepancy found during a special inspection? -
(answer)If it is not corrected by the contractor. 2009 IBC, Section 1704.1.2
According to the Model Program for Special Inspection, the special inspector is to document work that is
nonconforming: - (answer)In a written report - Section II B 4 - Model Programs
According to the Model Program for Special Inspection, the special inspector is to prepare written report
of inspection: - (answer)After each inspection visit - Section II B 5 - Model Programs
According to the Model Program for Special Inspection, which of the following items does not need to
be included in each inspection report? - (answer)Description of discussions with the contractor - Section
B 5 - Model Programs
According to the Specification for Structural Joints using high strength bolts, the nominal diameter of
standard bolt holes shall be how much larger than the nominal bolt diameter? - (answer)1/16 inch -
Specification for Structural Joints Table 3.1
,ICC Bolting EXAM (updated 2026) Questions & Answers | With 100%
Correct Answers graded A+ Guaranteed Pass!!!!!!
Discrepancies in the work shall be brought to the immediate attention of the "blank" for corrective
action. - (answer)the contractor - 2009 IBC, Section 1704.1.2.
The special inspector shall furnish inspection reports to the "blank" and to the "blank"? -
(answer)Building Official and Registered Design professional
The special inspector shall provide continuos inspection of: - (answer)Single-pass fillet welds greater
than 5/16 inch in size - 2099 IBC, Table 1704.3, Item 5.3
The special inspections required by this code are not required where the work is done on the premise of
a? - (answer)Approved fabricator - 2009 IBC, Section 1704.2.2
The special inspection of the steel fabrication process shall not be required where the fabricator does
not perform any? - (answer)heating operations - 2009 IBC, Section 1704.3, Exceptions # 1
According to the Specifications for Structural Steel Buildings, ASTM Standard "blank" is to be used for
the material test for steel sheets. - (answer)A568 - Section A31, Specifications for Structural Steel
Buildings
According to the Specifications for Structural Steel Buildings, the "blank" conducts the material tests for
identification of the structural steel. - (answer)Fabricator or Testing Laboratory - Section A31,
Specifications for Structural Steel Buildings.
According to the Specifications for Structural Steel Buildings, which of the following steel members are
allowed to be unidentified steel? - (answer)Unimportant members, where their physical properties and
weldability would not affect the structure strength - Section A31b, Specifications for Structural Steel
Buildings
, ICC Bolting EXAM (updated 2026) Questions & Answers | With 100%
Correct Answers graded A+ Guaranteed Pass!!!!!!
According to the Code of Standard Practice for Steel Buildings and Bridges, how is steel of special
material to be identified? - (answer)It is marked by the supplier - Section 5.1.1, Code of Standard
Practice for Steel Buildings and Bridges
According to the Code of Standard Practice for Steel Buildings and Bridges, how are fabricators stock
steel material identified? - (answer)Certified mill test reports - Section 5.2.2 - Code of Standard Practice
for Steel Buildings and Bridges
According to the Specification for Structural Steel Buildings, what ASTM Standard would apply to a
sample for structural steel pipe? - (answer)A53 - Section A31a - Specification for Structural Steel
Buildings
According to the Code of Standard Practice for Steel Buildings and Bridges, the number of samples
required to be tested for structural steel is: - (answer)The number specified by the ASTM specification -
Section 5.1.1 - Code of Standard Practice for Steel Buildings and Bridges
According to the Specification for Structural Steel Buildings, which ASTM standard would apply to a
sample for structural steel plates? - (answer)A36, A283, and A242 - Section A31a - Specification for
Structural Steel Buildings
According to the Specification for Structural Steel Buildings, "blank" tests are required for samples for
built-up sections consisting of plates over 2 inches in thickness. - (answer)Charpy V-notch testing -
Section A31d, Specification for Structural Steel Buildings
According to the Specification for Structural Steel Buildings, ASTM standard "blank" would apply to a
sample for structural steel bars. - (answer)A36, A529, and A572 - Specification for Structural Steel
Buildings
