Florida Air Conditioning Contractors Complete Exam Study Questions with 100% Correct Answers | Brand New Version

Florida Air Conditioning Contractors Complete Exam Study Questions with 100% Correct Answers | Brand New Version 1. Platform length support limit - ANSWER Each end of a platform 10 feet or more in length shall not exceed its support more than 30 inches. 2. Maximum hanger spacing for ducts - ANSWER The maximum hanger spacing for a duct sized less than 48 inches wide and less than 48 inches high is 5 feet. 3. Safe working load (SWL) - ANSWER A rope with a 20,000-pound capacity and a safety factor of 4 has a safe working load (SWL) of 5 tons.. 4. Slip and drive gauge requirement - ANSWER Slips and drives must not be less two gage(s) lighter than the duct wall nor below 24 gauge. 5. Sheave diameter strength efficiency - ANSWER A 6-inch sheave diameter when using a ¾-inch rope will produce a strength efficiency of 86 percent. 6. Commercial kitchen make-up air - ANSWER The amount of commercial kitchen make-up air supplied to the building from all sources shall be approximately equal to the amount of exhausted air. 7. Motor mounting styles - ANSWER All of the following are motor mounting styles except semi rigid. 8. Shut off valve installation - ANSWER A shut off valve shall be installed on the fuel oil supply line within reach. 9. Recommended superheat setting for low temperature evaporators - ANSWER 5 to 8 °F 10. Part of the thermal expansion valve that fastens the valve to the refrigerant piping - ANSWER valve body 11. Joining method for polyethylene pipe - ANSWER Adhesives and plastic fittings 12. Temperature-rise ratings for greater efficiency of a dry-type transformer - ANSWER 150 °F 13. Minimum Annual Fuel Utilization Efficiency (AFUE) for most furnaces - ANSWER 80 percent 14. Methods of controlling bacteria - ANSWER Encapsulation and electroporation 15. Minimum space between deep-fat fryer and surface flames - ANSWER 6 inches 16. Halide leak detectors detection capability - ANSWER 1 ounce per year 17. Type of eye splice not commonly used by wire rope manufacturers - ANSWER A fold back type 18. Minimum net exhaust flow rate for medium-duty cooking appliance - ANSWER 200 cfm per linear foot of hood length 19. Weight of a 22-gauge galvanized steel sheet - ANSWER 1.1562 pounds per square foot 20. Maximum air infiltration rate for skylights - ANSWER 0.3 cfm/ft2 21. Minimum width of heat seal tape - ANSWER All heat seal tape shall be a minimum width of 2 inch(es). 22. Ladder rung spacing - ANSWER Rungs of portable ladders and fixed ladders shall be spaced not less than 12 inches apart. 23. Face velocity for air coolers - ANSWER Random media air coolers are typically designed so that the wetted pads have a face velocity from 90 to 250 fpm so that the pressure drop remains below 0.1 in wg. 24. Refrigerant system requirement - ANSWER A capture system shall be provided for all systems containing 55 lbs. or more of refrigerant. 25. Discharge position identification - ANSWER The discharge position is identified by all except CCWBADD. 26. Grease duct construction thickness - ANSWER Grease ducts shall be constructed of stainless steel having a minimum thickness of 18 gauge. 27. Maximum temperature for solar systems - ANSWER Solar systems or solar-assisted systems shall be designed, constructed and controlled so that the temperature in the supply system shall not exceed 275°F. 28. Avoidance in duct installation - ANSWER Where electrical, fossil fuel, or solar energy collection heat sources are installed in air ducts, the installation shall avoid the creation of a fire hazard. 29. PPE responsibility - ANSWER The Employer is responsible for requiring of wearing of appropriate PPE in all operations. 30. Laying length of gate valve - ANSWER The laying length of a 2-inch cast iron flanged wedge gate valve with a pressure of 175 psi is 7 ¼ inches. 31. Smallest angle for duct installation - ANSWER The smallest angle he can use is 1 ¼" x 1 ¼" x 3/16". 32. Symptoms of refrigerant shortage - ANSWER Symptoms of a shortage of refrigerant include all of the following except high superheat. 33. Fan belt tension deflection - ANSWER When a fan belt is grasped and checking tension, you should obtain about a ½ inch deflection when finger pressure is applied. 34. Fusible links temperature rating - ANSWER The HVAC system normally operates at 184 degrees. The fusible links shall have a temperature rating of approximately 200 degrees.