CDC 1-5 QUIZ QUESTIONS AND VERIFIED ANSWERS |
100% ACCURATE
Training records are maintained electronically via - Answers - AF approved
Maintenance Information System (MIS) or equivalent
Which chapter in DAFMAN 91-203, Air Force Occupational Safety Fire and Health
Standards, provides guidance on electrical safety? - Answers - Chapter 8
A _____________ requires a 90 degree clockwise twist to couple. - Answers - Breech
coupling connector
When repairing braided shield wire if the hole in the braiding is ______ or less of the
wiring harness diameter use ____________. - Answers - 50%, self-bonding silicon tape
Which Air Force instruction provides guidance for proper handling of hazardous material
by all personnel that may be exposed? - Answers - AFI 90-821, Hazard Communication
Program
Normally, slack between support points should NOT exceed ________. - Answers - 0.5
inch
What inspection is performed between flight inspection of aircraft components when an
immediate turnaround or continuation flight is scheduled? - Answers - Thru Flight
inspection
Where would we look for demilitarization requirements? - Answers - DoD manual
4160.28, Defense Demilitarization: Demilitarization Procedures
When it comes to acquiring hazardous materials use the _________. - Answers -
Hazardous Materials Management Process (HMMP)
__________ provides guidance on corrosion control. - Answers - TO 1-1-691
________ drives the proper disposal of hazards and environmental protection from the
hazardous waste that is produced. - Answers - AFMAN 32-7002, Environmental
Compliance and Pollution Prevention
What regulation can help you understand the role Logistics Readiness Squadron (LRS)
plays in handling materials and items? - Answers - DAFI 23-101, Material Management
Policy
, The contents of your shop bench stock will be determined in accordance with
______________. - Answers - DAFMAN 23-122, Material Management Procedures
_______ incorporate all other files and are also a new edition of the publication. -
Answers - Revision
What type of defect is inoperable systems or other mission limiting discrepancies that
are suspected as non-conformance to applicable specifications? - Answers - Major
defect
Which deficiency is an unacceptable condition or recommendation for an enhancement
that impacts the operational safety, suitability, and/or effectiveness of a system,
subsystem, or component? - Answers - Material
Which of the following codes would be considered a due in from maintenance (DIFM)
asset? - Answers - XD2
Highlights an essential procedure, which, if not strictly observed, could result in damage
to, or destruction of, equipment or loss of mission effectiveness. - Answers - Cautions
On what part of the AFTO Form 244 would you look to find scheduled inspections? -
Answers - Pt. III
What regulation gives in depth information for filling out AF Form 2005? - Answers -
AFH 23-123V2, ILS-S Material Management Operations
What priority of change request could cause, personnel injury; damage to equipment;
reduce operational efficiency, and/or jeopardize the safety of success of the mission if
NOT corrected? - Answers -
What categories are assigned to explosive ordnance disposal (EOD)? - Answers -
Category 60
What are bench stock levels based on? - Answers - Consumption
Supply Chain Management (SCM) is a program accessed via the ________. - Answers
- Autonomic Logistics Information System (ALIS)
When Lightening II Support Equipment Management System (LSEMS) is in use, how
frequent does a wall-to-wall inventory have to be completed after the initial inventory? -
Answers - Annually
F-22 users must ensure the ________ matches with information in the Integrated
Maintenance Data System (IMDS). - Answers - Integrated Maintenance Information
System (IMIS)
100% ACCURATE
Training records are maintained electronically via - Answers - AF approved
Maintenance Information System (MIS) or equivalent
Which chapter in DAFMAN 91-203, Air Force Occupational Safety Fire and Health
Standards, provides guidance on electrical safety? - Answers - Chapter 8
A _____________ requires a 90 degree clockwise twist to couple. - Answers - Breech
coupling connector
When repairing braided shield wire if the hole in the braiding is ______ or less of the
wiring harness diameter use ____________. - Answers - 50%, self-bonding silicon tape
Which Air Force instruction provides guidance for proper handling of hazardous material
by all personnel that may be exposed? - Answers - AFI 90-821, Hazard Communication
Program
Normally, slack between support points should NOT exceed ________. - Answers - 0.5
inch
What inspection is performed between flight inspection of aircraft components when an
immediate turnaround or continuation flight is scheduled? - Answers - Thru Flight
inspection
Where would we look for demilitarization requirements? - Answers - DoD manual
4160.28, Defense Demilitarization: Demilitarization Procedures
When it comes to acquiring hazardous materials use the _________. - Answers -
Hazardous Materials Management Process (HMMP)
__________ provides guidance on corrosion control. - Answers - TO 1-1-691
________ drives the proper disposal of hazards and environmental protection from the
hazardous waste that is produced. - Answers - AFMAN 32-7002, Environmental
Compliance and Pollution Prevention
What regulation can help you understand the role Logistics Readiness Squadron (LRS)
plays in handling materials and items? - Answers - DAFI 23-101, Material Management
Policy
, The contents of your shop bench stock will be determined in accordance with
______________. - Answers - DAFMAN 23-122, Material Management Procedures
_______ incorporate all other files and are also a new edition of the publication. -
Answers - Revision
What type of defect is inoperable systems or other mission limiting discrepancies that
are suspected as non-conformance to applicable specifications? - Answers - Major
defect
Which deficiency is an unacceptable condition or recommendation for an enhancement
that impacts the operational safety, suitability, and/or effectiveness of a system,
subsystem, or component? - Answers - Material
Which of the following codes would be considered a due in from maintenance (DIFM)
asset? - Answers - XD2
Highlights an essential procedure, which, if not strictly observed, could result in damage
to, or destruction of, equipment or loss of mission effectiveness. - Answers - Cautions
On what part of the AFTO Form 244 would you look to find scheduled inspections? -
Answers - Pt. III
What regulation gives in depth information for filling out AF Form 2005? - Answers -
AFH 23-123V2, ILS-S Material Management Operations
What priority of change request could cause, personnel injury; damage to equipment;
reduce operational efficiency, and/or jeopardize the safety of success of the mission if
NOT corrected? - Answers -
What categories are assigned to explosive ordnance disposal (EOD)? - Answers -
Category 60
What are bench stock levels based on? - Answers - Consumption
Supply Chain Management (SCM) is a program accessed via the ________. - Answers
- Autonomic Logistics Information System (ALIS)
When Lightening II Support Equipment Management System (LSEMS) is in use, how
frequent does a wall-to-wall inventory have to be completed after the initial inventory? -
Answers - Annually
F-22 users must ensure the ________ matches with information in the Integrated
Maintenance Data System (IMDS). - Answers - Integrated Maintenance Information
System (IMIS)
