AMT2 SWE "A" Study Guide | 100% Correct
Answers | Verified | Latest 2024 Version
How do you clean helmet visor? - ✔✔SOFT CLOTH AND MILD SOAP SOLUTION; RINSE WITH CLEAN
WATER.
IAW 13520.1B ENCL 4-31
How do you clean flight gloves? - ✔✔
1. DON THE GLOVES.
2. WASH WITH SOAP AND WATER AS IF WASHING HANDS.
3. WHEN GLOVES ARE CLEAN, RINSE AND REMOVE FROM HANDS.
4. SQUEEZE, BUT DO NOT WRING GLOVES TO REMOVE EXCESS WATER.
5. PLACE THE GLOVES FLAT ON A TOWEL, AND FOLD THE TOWEL TO COVER
GLOVES MAKING SURE GLOVES DO NOT CONTACT EACH OTHER.
IAW 13520.1B ENCL 5 PAGE 7-27
What is the limit for light corrosion? - ✔✔A DEPTH OF APPROXIMATELY ONE MIL (0.001 inch)
IAW AFTO 1-1A-691 PAGE 4-9
What is a sequencing valve use for in the landing gear? - ✔✔THESE UNITS ARE SO INTERCONNECTED
THAT THEY PERMIT PROPERLY SEQUENCED RETRACTION
AND EXTENSION OF THE LANDING GEAR AND THE LANDING GEAR DOORS.
IAW A&P GENERAL HANDBOOK PAGE 349
What are torque links purposes? - ✔✔TORQUE LINKS (FIGURE 9-10) KEEP THE LANDING GEAR POINTED
IN A STRAIGHT-AHEAD DIRECTION; ONE TORQUE LINK CONNECTS TO THE SHOCK STRUT CYLINDER,
WHILE THE OTHER CONNECTS TO THE PISTON.
IAW A&P AIRFRAME HANDBOOK PAGE 348
What candle power is the mirror? - ✔✔WHEN USED ON A BRIGHT SUNNY DAY THE EMERGENCY
SIGNALING MIRROR HAS A REFLECTIVE GLARE OF 8 MILLIO NCANDLE POWER (VISIBLE UP TO 40 MILES).
,IAW 13520.1B PAGE 4-26
Cold weather aircrew survival kit contains enough supplies for how many people? - ✔✔EACH
CONTAINER IN THE CWASK WILL HAVE ENOUGH SURVIVAL EQUIPMENT
FOR FOUR CREWMEMBERS.
IAW 13520 PAGE 4-52
Form number for flight gear issue? - ✔✔CG-538
IAW 13520.1B ENCL 1-1
How do you preserve a engine oil system? - ✔✔MAINTAIN CLEAN AND FULL
IAW NAV AIR 15-01-500 PAGE 2-2
Color of TOPS form? - ✔✔GREEN
IAW PG-85-00-110 PAGE 3-3
Prop protractor has unit of measurement is? - ✔✔DEGREE'S
In which direction do you blend a compressor blade? - ✔✔ROOT TO TIP
Where is the damage worse on a compressor blade? - ✔✔ROOT
Major disadvantage of a axial compressor blade? - ✔✔THE AXIAL-FLOW COMPRESSOR'S
DISADVANTAGES ARE:
(1) GOOD EFFICIENCIES OVER ONLY NARROW ROTATIONAL SPEED RANGE.
(2) DIFFICULTY OF MANUFACTURE AND HIGH COST.
(3) RELATIVELY HIGH WEIGHT.
(4) HIGH STARTING POWER REQUIREMENTS. 9 (THIS HAS BEEN PARTIALLY OVERCOME BY SPLIT
COMPRESSORS.)
IAW A&P POWERPLANT HANDBOOK PAGE 48
,Max amount with out a report and survey? - ✔✔500 OR LESS
Type 3 material cost? - ✔✔TYPE 3 CONSUMABLE AERONAUTICAL MATERIEL, LESS AVIONICS, WITH A
UNIT PRICE LESS THAN
$250 AND PROCURABLE FROM AN OGA SOURCE. UNITS SET THEIR OWN ALLOWANCE QUANTITIES
AND PROCURE MATERIEL USING UNIT AFC 30 FUNDS.
IAW PG-85-00-110 PAGE 6-2
UR tag? - ✔✔CG-1577A
IAW PG-85-00-130 PAGE 1-6
Urgent UR message routed through Whom? - ✔✔URGENT INTERIM UR MESSAGES SHALL BE ADDRESSED
TO ARSC, ACMS, AND INFO COMMANDANT (CG-41). ARSC QUALITY ASSURANCE SUPPLY (QAS) AND
ACMS SHALL BE INCLUDED AS ADDRESSEES ON UR MESSAGES.
IAW PG-85-00-130 PAGE 1-1
What Mil spec does ATA chapter conform to? - ✔✔MIL-STD-1808
IAW PG-85-00-110 PAGE 3-1
Max allowable flight time in a month? - ✔✔A FLIGHT CREW MEMBER SHALL NOT FLY AS A CREW
MEMBER MORE THAN 125 HOURS DURING ANY 30 CONSECUTIVE DAYS.
IAW 3710.1F PAGE 3-17
Max allowable flight time in a week? - ✔✔A FLIGHT CREW MEMBER SHALL NOT FLY AS A CREW MEMBER
MORE THAN 50 HOURS IN
ANY SEVEN CONSECUTIVE DAYS.
IAW 3710.1F PAGE 3-17
Material in a Brown cylinder? - ✔✔TOXIC AND POISIONOUS MATERIALS IAW M10360.3 PAGE 13-6
How a propeller blade measured? Compressor blade? - ✔✔10TH OF A DEGREE
, Minimum amount of time to test a cable? - ✔✔3 MIN
After how long do you need a warm-up flight? - ✔✔AN AIRCREW MEMBER THAT HAS NOT FLOWN IN HIS
OR HER PRIMARY AIRCREW
DESIGNATION (IN-FLIGHT OR IN AN APPROVED SIMULATOR) DURING THE PREVIOUS 30 DAYS
IS REQUIRED TO FLY A WARM-UP TRAINING FLIGHT IN THEIR PRIMARY AIRCREW DESIGNATION
PRIOR TO FLYING IN THAT CREW POSITION ON AN OPERATIONAL MISSION.
IAW 3710.1F PAGE 8-40
UR process guide number? - ✔✔PG-85-00-130
IAW PG-85-00-130
How do you finish a compressor blade? - ✔✔DAMAGE SUCH AS BURRS, NICKS, SCRATCHES, SCORING, OR
GALLING SHOULD BE REMOVED WITH A FINE OIL STONE, CROCUS CLOTH, OR ANY SIMILAR ABRASIVE
SUBSTANCE.
IAW A&P POWERPLANT HANDBOOK PAGE 414
Symbol or color for falling hazards? - ✔✔YELLOW FOR HAZARD MARKING. YELLOW (13538) IS THE
ACCEPTED COLOR USED TO PAINT STRIKING, STUMBLING, AND FALLING HAZARDS. WHERE SUITABLE,
ALTERNATE BANDS OF BLACK AND YELLOW SHALL BE USED.
IAW COLOR AND COATING MANUAL M10360 PAGE 10-2
Min distance for servicing nitrogen? - ✔✔THOSE PERSONS NOT DIRECTLY INVOLVED IN NITROGEN
SERVICING OPERATIONS SHOULD STAY OUTSIDE A 20-FOOT RADIUS OF THE SERVICING POINT.
IAW NAV AIR 00-25-172 PAGE 4-17
Type 1 preservation? - ✔✔LEVEL I PRESERVATION PROTECTS IDLE/INACTIVE AIRCRAFT FOR A MAXIMUM
OF 90 DAYS. THE BASIC FOUNDATION OF LEVEL I PROTECTION IS TO ENSURE ALL SYSTEMS ARE KEPT
FREE OF WATER AND FLUIDS ARE TOPPED OFF. SPRAY OR BRUSH-ON THIN CORROSION PREVENTIVE
COMPOUNDS ARE APPLIED TO BARE SURFACES TO PROVIDE A MECHANICAL BARRIER SEPARATING
METAL FROM MOISTURE. WATER AND FOREIGN OBJECT INTRUSION AREAS ARE SEALED WITH TAPE AND
BARRIER (T&B) MATERIAL AND PROTECTIVE COVERS.
IAW NAV AIR 15-01-500 PAGE2-3
Answers | Verified | Latest 2024 Version
How do you clean helmet visor? - ✔✔SOFT CLOTH AND MILD SOAP SOLUTION; RINSE WITH CLEAN
WATER.
IAW 13520.1B ENCL 4-31
How do you clean flight gloves? - ✔✔
1. DON THE GLOVES.
2. WASH WITH SOAP AND WATER AS IF WASHING HANDS.
3. WHEN GLOVES ARE CLEAN, RINSE AND REMOVE FROM HANDS.
4. SQUEEZE, BUT DO NOT WRING GLOVES TO REMOVE EXCESS WATER.
5. PLACE THE GLOVES FLAT ON A TOWEL, AND FOLD THE TOWEL TO COVER
GLOVES MAKING SURE GLOVES DO NOT CONTACT EACH OTHER.
IAW 13520.1B ENCL 5 PAGE 7-27
What is the limit for light corrosion? - ✔✔A DEPTH OF APPROXIMATELY ONE MIL (0.001 inch)
IAW AFTO 1-1A-691 PAGE 4-9
What is a sequencing valve use for in the landing gear? - ✔✔THESE UNITS ARE SO INTERCONNECTED
THAT THEY PERMIT PROPERLY SEQUENCED RETRACTION
AND EXTENSION OF THE LANDING GEAR AND THE LANDING GEAR DOORS.
IAW A&P GENERAL HANDBOOK PAGE 349
What are torque links purposes? - ✔✔TORQUE LINKS (FIGURE 9-10) KEEP THE LANDING GEAR POINTED
IN A STRAIGHT-AHEAD DIRECTION; ONE TORQUE LINK CONNECTS TO THE SHOCK STRUT CYLINDER,
WHILE THE OTHER CONNECTS TO THE PISTON.
IAW A&P AIRFRAME HANDBOOK PAGE 348
What candle power is the mirror? - ✔✔WHEN USED ON A BRIGHT SUNNY DAY THE EMERGENCY
SIGNALING MIRROR HAS A REFLECTIVE GLARE OF 8 MILLIO NCANDLE POWER (VISIBLE UP TO 40 MILES).
,IAW 13520.1B PAGE 4-26
Cold weather aircrew survival kit contains enough supplies for how many people? - ✔✔EACH
CONTAINER IN THE CWASK WILL HAVE ENOUGH SURVIVAL EQUIPMENT
FOR FOUR CREWMEMBERS.
IAW 13520 PAGE 4-52
Form number for flight gear issue? - ✔✔CG-538
IAW 13520.1B ENCL 1-1
How do you preserve a engine oil system? - ✔✔MAINTAIN CLEAN AND FULL
IAW NAV AIR 15-01-500 PAGE 2-2
Color of TOPS form? - ✔✔GREEN
IAW PG-85-00-110 PAGE 3-3
Prop protractor has unit of measurement is? - ✔✔DEGREE'S
In which direction do you blend a compressor blade? - ✔✔ROOT TO TIP
Where is the damage worse on a compressor blade? - ✔✔ROOT
Major disadvantage of a axial compressor blade? - ✔✔THE AXIAL-FLOW COMPRESSOR'S
DISADVANTAGES ARE:
(1) GOOD EFFICIENCIES OVER ONLY NARROW ROTATIONAL SPEED RANGE.
(2) DIFFICULTY OF MANUFACTURE AND HIGH COST.
(3) RELATIVELY HIGH WEIGHT.
(4) HIGH STARTING POWER REQUIREMENTS. 9 (THIS HAS BEEN PARTIALLY OVERCOME BY SPLIT
COMPRESSORS.)
IAW A&P POWERPLANT HANDBOOK PAGE 48
,Max amount with out a report and survey? - ✔✔500 OR LESS
Type 3 material cost? - ✔✔TYPE 3 CONSUMABLE AERONAUTICAL MATERIEL, LESS AVIONICS, WITH A
UNIT PRICE LESS THAN
$250 AND PROCURABLE FROM AN OGA SOURCE. UNITS SET THEIR OWN ALLOWANCE QUANTITIES
AND PROCURE MATERIEL USING UNIT AFC 30 FUNDS.
IAW PG-85-00-110 PAGE 6-2
UR tag? - ✔✔CG-1577A
IAW PG-85-00-130 PAGE 1-6
Urgent UR message routed through Whom? - ✔✔URGENT INTERIM UR MESSAGES SHALL BE ADDRESSED
TO ARSC, ACMS, AND INFO COMMANDANT (CG-41). ARSC QUALITY ASSURANCE SUPPLY (QAS) AND
ACMS SHALL BE INCLUDED AS ADDRESSEES ON UR MESSAGES.
IAW PG-85-00-130 PAGE 1-1
What Mil spec does ATA chapter conform to? - ✔✔MIL-STD-1808
IAW PG-85-00-110 PAGE 3-1
Max allowable flight time in a month? - ✔✔A FLIGHT CREW MEMBER SHALL NOT FLY AS A CREW
MEMBER MORE THAN 125 HOURS DURING ANY 30 CONSECUTIVE DAYS.
IAW 3710.1F PAGE 3-17
Max allowable flight time in a week? - ✔✔A FLIGHT CREW MEMBER SHALL NOT FLY AS A CREW MEMBER
MORE THAN 50 HOURS IN
ANY SEVEN CONSECUTIVE DAYS.
IAW 3710.1F PAGE 3-17
Material in a Brown cylinder? - ✔✔TOXIC AND POISIONOUS MATERIALS IAW M10360.3 PAGE 13-6
How a propeller blade measured? Compressor blade? - ✔✔10TH OF A DEGREE
, Minimum amount of time to test a cable? - ✔✔3 MIN
After how long do you need a warm-up flight? - ✔✔AN AIRCREW MEMBER THAT HAS NOT FLOWN IN HIS
OR HER PRIMARY AIRCREW
DESIGNATION (IN-FLIGHT OR IN AN APPROVED SIMULATOR) DURING THE PREVIOUS 30 DAYS
IS REQUIRED TO FLY A WARM-UP TRAINING FLIGHT IN THEIR PRIMARY AIRCREW DESIGNATION
PRIOR TO FLYING IN THAT CREW POSITION ON AN OPERATIONAL MISSION.
IAW 3710.1F PAGE 8-40
UR process guide number? - ✔✔PG-85-00-130
IAW PG-85-00-130
How do you finish a compressor blade? - ✔✔DAMAGE SUCH AS BURRS, NICKS, SCRATCHES, SCORING, OR
GALLING SHOULD BE REMOVED WITH A FINE OIL STONE, CROCUS CLOTH, OR ANY SIMILAR ABRASIVE
SUBSTANCE.
IAW A&P POWERPLANT HANDBOOK PAGE 414
Symbol or color for falling hazards? - ✔✔YELLOW FOR HAZARD MARKING. YELLOW (13538) IS THE
ACCEPTED COLOR USED TO PAINT STRIKING, STUMBLING, AND FALLING HAZARDS. WHERE SUITABLE,
ALTERNATE BANDS OF BLACK AND YELLOW SHALL BE USED.
IAW COLOR AND COATING MANUAL M10360 PAGE 10-2
Min distance for servicing nitrogen? - ✔✔THOSE PERSONS NOT DIRECTLY INVOLVED IN NITROGEN
SERVICING OPERATIONS SHOULD STAY OUTSIDE A 20-FOOT RADIUS OF THE SERVICING POINT.
IAW NAV AIR 00-25-172 PAGE 4-17
Type 1 preservation? - ✔✔LEVEL I PRESERVATION PROTECTS IDLE/INACTIVE AIRCRAFT FOR A MAXIMUM
OF 90 DAYS. THE BASIC FOUNDATION OF LEVEL I PROTECTION IS TO ENSURE ALL SYSTEMS ARE KEPT
FREE OF WATER AND FLUIDS ARE TOPPED OFF. SPRAY OR BRUSH-ON THIN CORROSION PREVENTIVE
COMPOUNDS ARE APPLIED TO BARE SURFACES TO PROVIDE A MECHANICAL BARRIER SEPARATING
METAL FROM MOISTURE. WATER AND FOREIGN OBJECT INTRUSION AREAS ARE SEALED WITH TAPE AND
BARRIER (T&B) MATERIAL AND PROTECTIVE COVERS.
IAW NAV AIR 15-01-500 PAGE2-3
