Page | 1
ACI GRADE 1 FIELD TESTING CERTIFICATION
PRACTICE TEST – IRVING 2025| BRAND NEW
ACTUAL EXAM WITH 100% VERIFIED QUESTIONS
AND CORRECT SOLUTIONS| GUARANTEED VALUE
PACK| ACE YOUR GRADES.
If the concrete contains coarse aggregate particles that would be
retained on a 1-1/2 in sieve, the concrete must be wet sieved to
remove large sizes before testing in the rollameter. (T or F) -
correct answer - True
, Page | 2
The rollameter may be used for concretes containing lightweight
or normal weight aggregates. (T or F) - correct answer - True
The calibrated measuring cup is equivalent to approximately 1%
of the volume of the bowl of the air meter. (T or F) - correct
answer - True
Always add isopropyl alcohol prior to the initial filling of the meter
with liquid. (T or F) - correct answer - False (Pint of water first)
Immediately after water is added and the cap is tightened, the
next step is: - correct answer - Invert and agitate the unit for at
least 45 seconds
Which of the following equipment is not used in the ASTM C173
tests? - correct answer - Strike off plate
After the meter had been rolled twice with no change in the liquid
level and no foam on the surface of the liquid, the direct reading
of the liquid in the neck was 3.25%. What was the air content of
, Page | 3
the concrete? The aggregate correction factor is 0.3% & 2 pints of
alcohol were added initially. - correct answer -
Read the liquid level in the neck, estimating to the nearest: -
correct answer - 0.25%
After the top is clamped on, fill the rollameter with liquid by: -
correct answer - Using the funnel until the liquid appears in the
neck
The rolling procedure must be performed: - correct answer - With
the neck of of the rollameter elevated
Standard concrete specimens for comprehensive strength tests
should be "initially" cured at 50 to 90° F. (T or F) - correct answer
- False
Standard compressive strength specimens for acceptance may
be 6 X 12 or 4 X 8 inch cylinders. (T or F) - correct answer - True
ACI GRADE 1 FIELD TESTING CERTIFICATION
PRACTICE TEST – IRVING 2025| BRAND NEW
ACTUAL EXAM WITH 100% VERIFIED QUESTIONS
AND CORRECT SOLUTIONS| GUARANTEED VALUE
PACK| ACE YOUR GRADES.
If the concrete contains coarse aggregate particles that would be
retained on a 1-1/2 in sieve, the concrete must be wet sieved to
remove large sizes before testing in the rollameter. (T or F) -
correct answer - True
, Page | 2
The rollameter may be used for concretes containing lightweight
or normal weight aggregates. (T or F) - correct answer - True
The calibrated measuring cup is equivalent to approximately 1%
of the volume of the bowl of the air meter. (T or F) - correct
answer - True
Always add isopropyl alcohol prior to the initial filling of the meter
with liquid. (T or F) - correct answer - False (Pint of water first)
Immediately after water is added and the cap is tightened, the
next step is: - correct answer - Invert and agitate the unit for at
least 45 seconds
Which of the following equipment is not used in the ASTM C173
tests? - correct answer - Strike off plate
After the meter had been rolled twice with no change in the liquid
level and no foam on the surface of the liquid, the direct reading
of the liquid in the neck was 3.25%. What was the air content of
, Page | 3
the concrete? The aggregate correction factor is 0.3% & 2 pints of
alcohol were added initially. - correct answer -
Read the liquid level in the neck, estimating to the nearest: -
correct answer - 0.25%
After the top is clamped on, fill the rollameter with liquid by: -
correct answer - Using the funnel until the liquid appears in the
neck
The rolling procedure must be performed: - correct answer - With
the neck of of the rollameter elevated
Standard concrete specimens for comprehensive strength tests
should be "initially" cured at 50 to 90° F. (T or F) - correct answer
- False
Standard compressive strength specimens for acceptance may
be 6 X 12 or 4 X 8 inch cylinders. (T or F) - correct answer - True
