NEIEP 500 FINAL EXAM SET OF QUESTIONNS
AND CORRECT WELL DETAILED ANSWERS
ALREADY GRADED A+ GUARANTEED
SUSSESS
What is the minimum number of spare wires that should be pulled? - correct answer > 10%
When making connections at terminal posts, how should the traveling cables be connected? - correct
answer > on the top
What is the name for the complete metal system of duct, conduit and flex that protects the wiring? -
correct answer > Raceway
How is the work divided when planning piping and wiring of an elevator installation? - correct answer >
Hoistway, car and machine room
What document may be the only place to look for such information as type of fixtures, car panel, fire
service floor, etc? - correct answer > Job abstract
What information is shown on a pull sheet? - correct answer > Terminal connections
Which type of diagram shows a simplified path from positive to negative for all components in a circuit? -
correct answer > Straight line
How are multiple installations of traveling cables numbered for a single car? - correct answer > From the
rail regardless of placement in the hoistway
How many threads per in are there on a 10-24 machine screw? - correct answer > 24
Interlocks are always wired in what manner? - correct answer > series
, Why would you wear a grounding wrist strap? - correct answer > To prevent damage to sensitive solid
state circuits
How are wire sizes larger than 4/0 measured? - correct answer > In circular mils
What is the abbreviated term for current carry8ing capacity? - correct answer > Ampacity
What is the minimum size wired for lighting circuits in an elevator installation? - correct answer > #14
What is the special about wire used for the interlock circuit? - correct answer > It must be rated for 200
degrees C
What is the smallest wire that is permitted in an elevator installation? - correct answer > #24
When bending conduit, what is the maximum number of decrees of bend allowed between access points?
- correct answer > 90 degrees
What is the reference point on the thin-wall bender for the finish line of a back to back bend? - correct
answer > The star point
What is the total in degrees of the bends in a three-bend saddle? - correct answer > 90 degrees
You have 10' length of ¾" rigid conduit which needs to have a 90 degree bend with a 16" stub height.
With a 7" take- up, what is the distance from the end of the pipe to the mark where the hickey arrow is
aligned? - correct answer > 9 inches
What is shown on the final layout? - correct answer > A plan drawing and an elevation giving dimensions
In the circuit shown, which is the common wired for the second level? - correct answer > DC+
AND CORRECT WELL DETAILED ANSWERS
ALREADY GRADED A+ GUARANTEED
SUSSESS
What is the minimum number of spare wires that should be pulled? - correct answer > 10%
When making connections at terminal posts, how should the traveling cables be connected? - correct
answer > on the top
What is the name for the complete metal system of duct, conduit and flex that protects the wiring? -
correct answer > Raceway
How is the work divided when planning piping and wiring of an elevator installation? - correct answer >
Hoistway, car and machine room
What document may be the only place to look for such information as type of fixtures, car panel, fire
service floor, etc? - correct answer > Job abstract
What information is shown on a pull sheet? - correct answer > Terminal connections
Which type of diagram shows a simplified path from positive to negative for all components in a circuit? -
correct answer > Straight line
How are multiple installations of traveling cables numbered for a single car? - correct answer > From the
rail regardless of placement in the hoistway
How many threads per in are there on a 10-24 machine screw? - correct answer > 24
Interlocks are always wired in what manner? - correct answer > series
, Why would you wear a grounding wrist strap? - correct answer > To prevent damage to sensitive solid
state circuits
How are wire sizes larger than 4/0 measured? - correct answer > In circular mils
What is the abbreviated term for current carry8ing capacity? - correct answer > Ampacity
What is the minimum size wired for lighting circuits in an elevator installation? - correct answer > #14
What is the special about wire used for the interlock circuit? - correct answer > It must be rated for 200
degrees C
What is the smallest wire that is permitted in an elevator installation? - correct answer > #24
When bending conduit, what is the maximum number of decrees of bend allowed between access points?
- correct answer > 90 degrees
What is the reference point on the thin-wall bender for the finish line of a back to back bend? - correct
answer > The star point
What is the total in degrees of the bends in a three-bend saddle? - correct answer > 90 degrees
You have 10' length of ¾" rigid conduit which needs to have a 90 degree bend with a 16" stub height.
With a 7" take- up, what is the distance from the end of the pipe to the mark where the hickey arrow is
aligned? - correct answer > 9 inches
What is shown on the final layout? - correct answer > A plan drawing and an elevation giving dimensions
In the circuit shown, which is the common wired for the second level? - correct answer > DC+
