ASE

ASE A4 practice test answered 2023 spring 2. A driver says that the front end of his car vibrates up and down while traveling at most road speeds. Tech A says that too much runout of the front wheels could be the cause. Tech B says that a static out of balance of the front wheels could be the cause. Who is right? A. Tech A only B. Tech B only C. Both A and B D. Neither A or B C. Both Techs are right. Too much runout or static out of balance in the front wheels will cause a vibration ...

ASE A5 Brakes Questions and Answers 2022/2023 A hydro-boost brake system has reduced braking performance. Technician A says to check the power steering system. Technician B says to check the vacuum check valve. Who is correct? TECH A is correct. The power steering pump produces pressure for the Hydro-Boost unit. A vehicle with power assisted brakes has a hard brake pedal. Which of the following is LEAST likely to cause this condition? A. Master cylinder. B. Vacuum check valve. C. Bra...

ASE Brakes A5 Test ( Exam 1 ), ASE A5 Brakes, ASE Brakes A5 ( Exam 3 ), ASE Brakes A5 Test ( Exam 2 ) answered 2023 A drum is chattering on the brake lathe. This could be a result of a. failure to install the dampening belt b. cutting too slowly c. dull cutting blades d. cutting speed too fast A : failure to install the dampening belt why : a missing dampening belt could cause the drum to vibrate while on the lathe. this vibration can cause the drum to bounce on the cutting tip ...

ASE BRAKES Exams #1-5 (Answered) Latest Spring A A drum is chattering on the brake lathe. This could be the result of: A. Failure to install the dampening belt. B. Cutting too slowly. C. Dull cutting blades. D. Cutting speed too fast. C A vehicle is equipped with a hydro-boost brake system has a hard pedal with little braking action. Which of the following could be the cause? A. Low brake fluid B. Air in the brake fluid C. Low power steering fluid D. An overtightened power steerin...

ASE (Entry level technician prep) - Brakes A5 A5 Question 1 The brake pedal is low and spongy; all brake adjustments have been completed according to specifications. The cause of the problem could be: A) Binding pedal linkage. B)Dented brake line. C)Plugged compensating port. D)A weak hydraulic hose. Answer D is correct! Binding pedal linkage would cause a hard pedal and perhaps an effective brake system. This is also true for a dented brake line. A plugged compensator port ma...

A spongy brake pedal may be caused by: a. ABS Diagnostic Trouble Code set b. Frozen caliper piston c. Defective metering valve. d. Air in hydraulic system D This question is not like the others. It has the word EXCEPT. For this question, look for the choice that could NOT cause the described situation. Read the entire question carefully before choosing your answer. A vehicle has a very erratic brake pulling concern while applying the brakes. All of the following items could cause this ...

2. A driver says that the front end of his car vibrates up and down while traveling at most road speeds. Tech A says that too much runout of the front wheels could be the cause. Tech B says that a static out of balance of the front wheels could be the cause. Who is right? A. Tech A only B. Tech B only C. Both A and B D. Neither A or B C. Both Techs are right. Too much runout or static out of balance in the front wheels will cause a vibration 3. A vehicle has front wheel shimmy at low...

Noise: In gear, clutch disengaged (pedal to floor) Pilot bushing or bearing Noise: Neutral, clutch disengaged (pedal to floor) Release bearing Noise: Neutral, clutch engaged (pedal up) Input shaft bearing Binding U-Joint will damage?? Extension housing bushing and seal What is used to check the clearance between the shift fork and the synchronizer sleeve? A feeler guage Warped pressure plates... ... should be replaced Ring and pinion gears... ...should be replaced as a set

What is the purpose of a brake band? It stops and holds the drum that is connected to a member of the planetary gearset. What are brake bands made out of? Brake bands are flexible steel plates lined with friction material. That material can be organic or semi-metallic. What aids in brake band hear dissipation? The friction material absorbs trans fluid. When the brake band tightens around the drum, why doesnt trans fluid get trapped in between the two surfaces? Trans fluid is squeezed...

an engine miss is being diagnosed using a cylinder leakage test. Technician A says that any cylinder with over 20% leakage has excessive leakage. Tech B says that air leaking from the tailpipe indicates a cracked cylinder. A only, B only, A & B, Neither . A only: If cylinder leakage exceeds 20%, check for air escaping the tailpipe, the PCV valve opening in the rocker arm cover, and the top of the throttle body or carburetor. Air leaking from the tailpipe usually indicates an exhau...